Ciena 170-3930-900 Скачать руководство пользователя страница 94

Страница: 94 / 104

8-8

Mounting Options

3930 Service Delivery Switch

Hardware Installation and Start-up Manual

009-3223-001 Standard Revision E

2012-2014 Ciena

Corporation

January 2014

Procedure 8-2

Installing the 19” Frame Mount Bracket - 1 RU

Step

Action

Align the holes of the mounting bracket with the holes on the side of the unit
(see

Figure 8-5

) as follows:

•

3930, 3932, 3940, 3960, 5142 and 5160 — install screws in holes 1
and 2.

•

3920 — install screws in holes 5 and 6.

Note:

When mounting a 3920, install the screws in the set of holes on the

side of the chassis that is located closest to the middle of the chassis.

Note:

When correctly installed, the mounting flange will be recessed

approximately 2 inches from the front faceplate of the chassis.

Figure 8-5
Mounting bracket, with holes labeled

Repeat

step 1

to install the second bracket.

Position the chassis in place in the frame.

Install four customer supplied screws in the slots on both the left and right
brackets.

Tighten all screws to ensure they make a firm connection between the
bracket and the frame.

Install the cable supports on the mounting brackets using the available screw
position and the two longer 8-32 screws provided in the kit. One screw is used
per bracket.

Figure 8-2 on page 8-4

shows the Cable Supports installed on

the mounting bracket.

Содержание 170-3930-900


































































































Результаты поиска

Содержание 170-3930-900

Отзывы:

Бренды по названию

Популярные бренды

Ciena 170-3930-900, Руководство по установке и запуску оборудования

Результаты поиска

Содержание 170-3930-900

Отзывы:

Бренды по названию

Популярные бренды