manualshive.com logo in svg

Ciena 170-3930-900, Руководство по установке и запуску оборудования

Поделиться
Скачать
Ciena 170-3930-900 Скачать руководство пользователя страница 28

2-12

   Installation

3930 Service Delivery Switch

Hardware Installation and Start-up Manual

009-3223-001   Standard    Revision E

Copyright

©

 2012-2014 Ciena

®

 Corporation

January 2014

Alarm Cable

The alarm cable is an optional component.

The 3930 supports 16 external alarm inputs. The alarm connector is located 
in the center/right section of the 3930 labeled 

ALARMS

. The 15 foot alarm 

cable has a high density 26-pin D-sub connector on one end, and bare wires 
on the other. These wires are then connected to a wire wrap panel. 

Of the 26 pins on the connector, there are 16 alarm sense connections to 
detect any combination of switch close or opens and 8 returns. Up to two 
alarm sense lines can be connected to each return. The alarm sense lines can 
be paired with any return, however, it is recommended that the sensed 
switches that are paired come from equipment that is commonly grounded. 
The alarm pinout is provided in 

Table 2-2 on page 2-12

.

See 

“Installing an Alarm Cable (Optional)” on page 2-24

 for a procedure.

Table 2-2
3930 Alarm Port Pin Assignments 

Pin #

Lead

Color

Pin #

Lead

Color

1

Alarm sense 15

WH/BL

14

Alarm sense return 4

RD/OR

2

Alarm sense 13

BL/WH

15

Alarm sense return 3

OR/RD

3

Alarm sense 11

WH/OR

16

Alarm sense return 2

RD/GR

4

Alarm sense 9

OR/WH

17

Alarm sense return 1

GR/RD

5

Alarm sense 7

WH/GR

18

Frame ground

No connect

6

Alarm sense 5

GR/WH

19

Alarm sense 16

RD/BR

7

Alarm sense 3

WH/BR

20

Alarm sense 14

BR/RD

8

Alarm sense 1

BR/WH

21

Alarm sense 12

RD/SL

9

Frame ground

No connect

22

Alarm sense 10

SL/RD

10

Alarm sense return 8

WH/SL

23

Alarm sense 8

BK/BL

11

Alarm sense return 7

SL/WH

24

Alarm sense 6

BL/BK

12

Alarm sense return 6

RD/BL

25

Alarm sense 4

BK/OR

13

Alarm sense return 5

BL/RD

26

Alarm sense 2

OR/BK

Содержание 170-3930-900









































































































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды