background image

General information about your detector:

The heterodyne detector (HD):

A   heterodyne   detector   works   similar   to   a   broadcast   receiver.   The 

frequency   you   have   chosen   will   be   subtracted   from   the  bat  call  with  a 

bandwidth of +/- 5 kHz transforming it to the audible range.

As an example : Detector is set to 42 kHz

Call frequency

Setting

Difference

Effect

48 kHz

 

6 kHz 

not/barely hearable

47 kHz

 

5 kHz

hearable

46 kHz

 

4 kHz

hearable

45 kHz

 

3 kHz

hearable

44 kHz

 

2 kHz

hearable

43 kHz

 

1 kHz

hearable

42 kHz

42 kHz

0 kHz

not hearable

41 kHz

 

1 kHz

hearable

40 kHz

 

2 kHz

hearable

39 kHz

 

3 kHz

hearable

38 kHz

 

4 kHz

hearable

37 kHz

 

5 kHz

hearable

36 kHz

 

6 kHz 

not/barely hearable

You can use the HD detector like a radio and search the whole ultrasonic  

range for bats. A bat call has a wider range than one frequency, so you  

will be able to hear it across the whole 10 kHz window of the detector. 

When turning the thumbwheel you can now hear the frequency and the 

volume changing. Try find the best and loudest playback of the call. The 

display then shows the peak frequency of the call.

Ultrasonic sources which emit single frequency sine or square wave signals 

will be heard on the detector as a beeping signal. If the frequency of the 

detector is similar to the frequency of the source there will be no audible 

signal at all. This is because you are subtracting the detector frequency 

from the source signal with the result of 0 kHz. If you now tune up or 

down you will hear a rising beep.

Heterodyne detectors are used for manual data collection. It is the easiest 

way to identify species in the field depending on the quality of the call and 

the shown frequency. It is very difficult or even impossible to gain results 

as precise as these by using FD or TE detectors in the field. If you want to 

analyse a recorded heterodyne signal you have to know the original call 

frequency.   The   benefit   of   analysing   software   is   very   limited   with   HD 

recordings.

Содержание Batz 2.0










Отзывы: