All the transmitters DOTTO allow controlling 1 automation or
group of automations for awnings and shutters.
All the transmitters DOTTO6 allow controlling individually or at
the same time up to 6 automations or groups of automations for
awnings or shutters.
FUNCTIONING OF THE BUTTONS UP, DOWN
AND STOP
UP
Activates the automation GOING UP
DOWN
Activates the automation GOING DOWN
STOP
it stops the automation
FUNCTIONING OF THE BUTTON PROG AND
DIP-SWITCHES
The button PROG and the DIPSWITCHES program the functions of
the control units controlled by the transmitters DOTTO. Read
carefully the section “PROGRAMMING OF THE FUNCTIONS BY
MEANS OF TRANSMITTERS OF THE RANGE DOTTO” in the
handbook of the control unit or in the one of the tubular motor
with integrated electronic card.
FUNCTIONING OF THE BUTTON SELC
By this button it is possible to select the channel to be used for
the radio transmission.
1.
Press button SELC until selected the desired channel: the
corresponding led is on for some seconds
2.
Press one of the buttons UP, DOWN or STOP to transmit the
control
To select all the channels at the same time press several times the
button SELC until all the leds are on.
To display the channel set, press once the button SELC.
FUNCTIONING OF THE BUTTON SELG
By this button it is possible to program and select the GROUPS of
channels to be used for the radio transmission. It is possible to
store up to 8 groups of channels; stored the eighth, a new group
will replace the first one.
1.
Press the button SELC until selected the first channel to link to
the group
2.
Press the button SELG: the led linked to the selected channel
starts blinking
3.
Press the button SELC until selected the second channel to link
4.
Press the button SELG: the led linked to the selected channel
starts blinking
5.
Repeat the procedure for all the desired channels: the leds
linked are on till the end of the procedure
6.
Once selected all the channels wait for the leds to switch off:
the group has been stored and it is possible to display it by
pressing the button SELG
When the groups are more than one, to select the desired group
proceed as follows:
1.
Press the button SELG several times until selected the desired
group: the leds linked to the channels are on for some
minutes
2.
Press one of the buttons UP, DOWN or STOP to transmit the
control
To delete all the groups stored proceed as follows:
1.
Press and release the button SELG: the last group used is
displayed by the leds.
2.
Press and hold the SELC key before the LEDs are turned off
3.
Then, without releasing the SELC key, press and hold the SELG
key also.
4.
Keep pressed both the buttons for some seconds until the leds
switch off: the groups have been deleted
REPLACING BATTERY
Replace the battery when the radio range power decrease or the
led light intensity becomes too feeble. Open the door of the
battery compartment and replace the two batteries respecting the
polarity shown by picture 2.
WARNING:
Batteries contain pollutant elements, must be
disposed of in accordance with environmental regulations
(CIBOFER INTERNATIONAL s.r.l. advise to use a specific disposal
system).Transmitter contains pollutant elements too; follow the
same procedure to dispose.
Should the batteries lose electrolytic substances, please replace
them immediately avoiding with care any contact with such
substances.
99/05/CE DIRECTIVE CONFORMITY
The DOTTO transmitters are in conformity with the provisions of
the following EC directive(s), and with the standard referenced
here below:
EN 60950, EN 301 489-1, EN 301 489-3, EN 300 220-2
Stefano Ciriello
Legal representative of
CIBOFER INTERNATIONAL s.r.l.
Carugate, 28/01/2010
ENGLISH
Power supply
2 x Lithium 3V (CR2032 230mAh)
Frequency
434,15 MHz
Range in open field
300 m
Max.absorption
< 25 mA
Dimensions
124x52x21 mm
Weight
55 g
