Chrysler Pacifica Hybrid 2018 Скачать руководство пользователя | Manualshive

Страница: 222 / 617

background image

4. Position the lap belt so that it is snug and lies low across

your hips, below your abdomen. To remove slack in the
lap belt portion, pull up on the shoulder belt. To loosen
the lap belt if it is too tight, tilt the latch plate and pull
on the lap belt. A snug seat belt reduces the risk of
sliding under the seat belt in a collision.

5. Position the shoulder belt across the shoulder and chest

with minimal, if any slack so that it is comfortable and
not resting on your neck. The retractor will withdraw
any slack in the shoulder belt.

6. To release the seat belt, push the red button on the

buckle. The seat belt will automatically retract to its
stowed position. If necessary, slide the latch plate down
the webbing to allow the seat belt to retract fully.

Lap/Shoulder Belt Untwisting Procedure

Use the following procedure to untwist a twisted lap/
shoulder belt.

1. Position the latch plate as close as possible to the anchor

point.

2. At about 6 to 12 inches (15 to 30 cm) above the latch

plate, grasp and twist the seat belt webbing 180 degrees
to create a fold that begins immediately above the latch
plate.

3. Slide the latch plate upward over the folded webbing.

The folded webbing must enter the slot at the top of the
latch plate.

4. Continue to slide the latch plate up until it clears the

folded webbing and the seat belt is no longer twisted.

Positioning The Lap Belt

220

SAFETY

«
...
220
221
222
223
224
...
»

Содержание Pacifica Hybrid 2018










































































































































































































































































































































































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для Pacifica Hybrid 2018

Бренд: GMC Страницы: 140

Бренд: JETBAG Страницы: 44

Бренд: AccuAir Страницы: 40

Бренд: Peak Страницы: 10

3-series convertible

Бренд: BMW Страницы: 98

Бренд: muth Страницы: 10

Бренд: EZTRUNK Страницы: 3

Бренд: Inbay Страницы: 20

Бренд: Oldsmobile Страницы: 2

Бренд: Saab Страницы: 15

Бренд: NavInc Страницы: 6

Denali 1094-0185-15

Бренд: E&G Classics Страницы: 3

Бренд: Metra Electronics Страницы: 2

Бренд: Horn Tools Страницы: 12

Бренд: ROADGEAR Страницы: 2

Ridesmart KMA-610

Бренд: KlipXtreme Страницы: 12

Бренд: Beeper Страницы: 2

Бренд: walser Страницы: 8

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды