Chrysler Pacifica CS 2004 Скачать руководство пользователя страница 33 | Manualshive

Страница: 33 / 370

Chrysler Pacifica CS 2004 Скачать руководство пользователя страница 33

Symptom:

*PCI BUS COMMUNICATION FAILURE

POSSIBLE CAUSES

WIRING HARNESS INTERMITTENT

OPEN PCI BUS CIRCUIT AT THE DATA LINK CONNECTOR (DLC)

PCI BUS CIRCUIT SHORTED TO VOLTAGE

MODULE SHORT TO VOLTAGE

PCI BUS CIRCUIT SHORTED TO GROUND

MODULE SHORT TO GROUND

TEST

ACTION

APPLICABILITY

1

Note: Determine which modules this vehicle is equipped with before begin-
ning.
Note: When attempting to communicate with any of the modules on this
vehicle, the DRB will display 1 of 2 different communication errors: a NO
RESPONSE message or a BUS +/- SIGNALS OPEN message.
Turn the ignition on.
Using the DRB, attempt to communicate with the following control modules:
Airbag Control Module
Body Control Module
MIC (INSTRUMENT CLUSTER)
Was the DRBIII

t

able to communicate with one or more Module(s)?

All

Yes

→

No

→

2

Turn the ignition off.
Note: Visually inspect the related wiring harness. Look for any chafed,
pierced, pinched, or partially broken wires.
Note: Visually inspect the related wire harness connectors. Look for broken,
bent, pushed out, or corroded terminals.
Note: If the DRB can not communicate with a single module, refer to the
category list for the related symptom.
Were any problems found?

All

Yes

→

Repair wiring harness/connectors as necessary.
Perform BODY VERIFICATION TEST - VER 1.

No

→

Test Complete.

27

COMMUNICATION

«
...
31
32
33
34
35
...
»

Содержание Pacifica CS 2004



















































































































































































































































































































































































Отзывы:

Нет отзывов