Chrysler Pacifica CS 2004 Скачать руководство пользователя страница 300 | Manualshive

Страница: 300 / 370

Chrysler Pacifica CS 2004 Скачать руководство пользователя страница 300

Symptom:

U110C-NO FUEL LEVEL BUS MESSAGE

When Monitored and Set Condition:

U110C-NO FUEL LEVEL BUS MESSAGE

When Monitored:

Ignition on.

Set Condition:

No fuel level BUS messages received by the PCM for 20 seconds.

POSSIBLE CAUSES

DTC RESET

COMMUNICATE WITH BCM

FUEL LEVEL BUS MESSAGE

PCI BUS CIRCUIT OPEN FROM PCM TO BCM

BCM

TEST

ACTION

APPLICABILITY

1

NOTE: If a fuel level circuit or performance DTC is set along with U110C,
diagnose the circuit/performance DTC before continuing.
Turn the ignition on.
With the DRBIII

t

, erase DTCs.

Start the engine on and off several times. Leave the engine running for at least 20
second each time.
With the DRBIII

t

, read DTCs.

Does the DTC reset?

All

Yes

→

No

→

Refer to the INTERMITTENT CONDITION symptom in the
Driveability category.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

2

Ignition on, engine not running.
With the DRBIII

t

, attempt to communicate with the BCM.

Can communication be established with the BCM?

All

Yes

→

No

→

Refer to the Communication Category and perform the appropri-
ate symptom related to no communication with BCM.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

3

Turn the ignition on.
Using the DRBIII

t

, read the Fuel Level parameter in the PCM.

Does the DRBIII

t

display a fuel level value?

All

Yes

→

Replace and program the Powertrain Control Module in accor-
dance with the Service Information.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

No

→

294

DRIVEABILITY - NGC

«
...
298
299
300
301
302
...
»

Содержание Pacifica CS 2004



















































































































































































































































































































































































Отзывы:

Нет отзывов