manualshive.com logo in svg

Chrysler Pacifica CS 2004, Руководство по обслуживанию, Страница: 25 / 370

Поделиться
Скачать
Chrysler Pacifica CS 2004 Скачать руководство пользователя страница 25

Symptom:

*NO RESPONSE FROM PCM (PCM SCI ONLY)

POSSIBLE CAUSES

CHECK PCM POWERS AND GROUNDS

PCM SCI TRANSMIT CIRCUIT SHORTED TO VOLTAGE

PCM SCI RECEIVE CIRCUIT SHORTED TO VOLTAGE

PCM SCI CIRCUITS SHORTED TOGETHER

PCM SCI TRANSMIT CIRCUIT SHORTED TO GROUND

PCM SCI RECEIVE CIRCUIT SHORTED TO GROUND

PCM SCI RECEIVE CIRCUIT OPEN

PCM SCI TRANSMIT CIRCUIT OPEN

POWERTRAIN CONTROL MODULE

TEST

ACTION

APPLICABILITY

1

Perform the symptom Checking PCM Power and Ground Circuits in the Driveability
category.
NOTE: With the DRBIII

t

in the generic scan tool mode, attempt to commu-

nicate with the PCM.
NOTE: If the DRBIII

t

can communicate with the PCM in the generic scan

tool mode, it may not be necessary to perform this step.
Did the vehicle pass this test?

All

Yes

→

Go To

2

No

→

Repair as necessary.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

2

Turn the ignition off.
Disconnect the DRBIII

t

from the DLC.

Disconnect the PCM harness connectors.
Turn the ignition on.
Measure the voltage of the SCI Transmit (PCM) circuit at the Data Link harness
connector (cav 7).
Is the voltage above 1.0 volt?

All

Yes

→

Repair the SCI Transmit (PCM) circuit for a short to voltage.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

No

→

Go To

3

3

Turn the ignition off.
Disconnect the DRBIII

t

from the DLC.

Disconnect the PCM harness connectors.
Turn the ignition on.
Measure the voltage of the SCI Receive (PCM) circuit at the Data Link harness
connector (cav 12).
Is the voltage above 1.0 volt?

All

Yes

→

Repair the SCI Receive (PCM) circuit for a short to voltage.
Perform POWERTRAIN VERIFICATION TEST VER - 1.

No

→

Go To

4

19

COMMUNICATION

Содержание Pacifica CS 2004



















































































































































































































































































































































































Отзывы:

Нет отзывов