Chrysler Pacifica CS 2004 Скачать руководство пользователя страница 235

Страница: 235 / 370

Symptom:

P0582-SPEED CONTROL VACUUM SOLENOID CIRCUIT

When Monitored and Set Condition:

P0582-SPEED CONTROL VACUUM SOLENOID CIRCUIT

When Monitored:

Ignition on. Speed Control active.

Set Condition:

The PCM detects an open or short to voltage in the Speed Control Vacuum

Control circuit. One Trip Fault.

POSSIBLE CAUSES

SPEED CONTROL SOLENOID OPERATION

SPEED CONTROL VACUUM SOLENOID

(V36) S/C VACUUM SOL CONTROL CIRCUIT SHORTED TO GROUND

(V36) S/C VACUUM SOL CONTROL CIRCUIT OPEN

PCM (VACUUM SOLENOID)

TEST

ACTION

APPLICABILITY

Ignition on, engine not running.
With the DRBIII

, read DTCs and record the related Freeze Frame data.

With the DRBIII

, actuate the Speed Control Vacuum Solenoid and note operation.

Does the Speed Control Vacuum Solenoid actuate properly?

All

Yes

→

Refer to the INTERMITTENT CONDITION symptom in the
Driveability category.
Perform POWERTRAIN VERIFICATION TEST VER - 4 - NGC.

→

Go To

Turn the ignition off.
Disconnect the Speed Control Servo harness connector.
Ignition on, engine not running.
With the DRBIII

, actuate the Speed Control Vacuum Solenoid.

Using a 12-volt test light connected to ground, probe the S/C Vacuum Control circuit.
Does the test light illuminate brightly and flash?

All

Yes

→

Replace the Speed Control Servo.
Perform POWERTRAIN VERIFICATION TEST VER - 4 - NGC.

→

Go To

229

DRIVEABILITY - NGC

Содержание Pacifica CS 2004



















































































































































































































































































































































































Результаты поиска

Содержание Pacifica CS 2004

Отзывы:

Chrysler Pacifica CS 2004, Руководство по обслуживанию, Страница: 235 / 370

Результаты поиска

Содержание Pacifica CS 2004

Отзывы: