Chrysler Pacifica CS 2004 Скачать руководство пользователя страница 112 | Manualshive

Страница: 112 / 370

Chrysler Pacifica CS 2004 Скачать руководство пользователя страница 112

TEST

ACTION

APPLICABILITY

2

Warning: The fuel system is under a constant pressure (even with the engine
off). Before testing or servicing any fuel system hose, fitting or line, the fuel
system pressure must be released.
Install a fuel pressure gauge.
Ignition on, engine not running.
With the DRBIII

t

, actuate the ASD Fuel System test and observe the fuel pressure

gauge.
NOTE: Fuel pressure specification is 400 KPa +/- 34 KPa (58 psi +/- 5 psi).
Turn the ignition off.
Choose a conclusion that best matches your fuel pressure reading.

All

Within Specification

Above Specification

Replace the fuel filter/pressure regulator.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

Caution: Stop All Actuations.

3

NOTE: If one of the O2 Sensors Signal or Return circuits are shorted to
ground or voltage, all the other O2 Sensor voltage readings will be affected.
NOTE: After the repairs have been made, verify proper O2 Sensor operation.
If all the O2 Sensor voltage readings have not returned to normal, follow the
diagnostic procedure for the remaining O2 Sensors.
Start the engine.
Allow the engine to reach normal operating temperature.
With the DRBIII

t

, read the O2 Sensor voltage.

Is the voltage switching between 2.5 and 3.4 volts?

All

Yes

→

No

→

4

Turn the ignition off.
NOTE: Allow the O2 Sensor to cool down before continuing the test. The O2
voltage should stabilize at 5.0 volts. Raising the hood may help in reducing
under hood temps.
Ignition on, engine not running.
With the DRBIII

t

, actuate the O2 Heater Test.

With the DRBIII

t

, monitor O2 Sensor voltage for at least 2 minutes.

Does the voltage stay above 4.5 volts?

All

Yes

→

Replace the O2 Sensor.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

No

→

5

Turn the ignition off.
Disconnect the hoses at the Evap Purge Solenoid.
Using a hand vacuum pump, apply 10 inches of vacuum to the Evap Purge Solenoid
vacuum source port on the component side.
Did the Evap Purge Solenoid hold vacuum?

All

Yes

→

No

→

Replace the EVAP Purge Solenoid.
Perform POWERTRAIN VERIFICATION TEST VER - 5 - NGC.

106

DRIVEABILITY - NGC

P0172-FUEL SYSTEM 1/1 RICH —

Continued

«
...
110
111
112
113
114
...
»

Содержание Pacifica CS 2004



















































































































































































































































































































































































Отзывы:

Нет отзывов