Chrysler Caravan 2003, Руководство пользователя

Страница: 52 / 1160

• Distance to Empty
•
Instantaneous Fuel Economy
• Trip Odometer
•
Time Elapsed
• Distance to Service Message
•
Off (Blank)
2. To set the magnetic variance zone when VARI-
ANCE = X (X = 1 - 15) is indicated in the VF
Display.
3. To select the displayed programmable feature
setting. (When equipped.)
MENU BUTTON (EVIC only)
For complete information of the programmable
features and memory messages, refer to the RS/RG
Service Manual.
Use the MENU button to sequentially step the
EVIC through the programmable features.
Use the MENU button to enter the Tire Pressure
Monitoring (TPM) Training Procedure.
RESET BUTTON
The RESET Button has two different functions:
1. To clear the trip functions that may be reset
2. To enter and exit the diagnostic mode
Pressing the RESET button once will clear the
trip function that is currently being displayed (ex-
cept Distance to Service) and the CMTC/EVIC will
send a PCI bus beep request to the BCM. If the
RESET button is pressed again within 3 seconds,
the CMTC/EVIC will reset ALL of the trip functions
and an additional beep request is sent to the BCM.
The trip functions that may be reset are:
• Average Fuel Economy
• Trip Odometer
•
Elapsed Time
A reset will only occur if one of the trip functions
that may be reset is currently being displayed.
Pressing the RESET button for more than three (3)
seconds resets the Distance to Service function
while the Distance to Service message is being
displayed. The CMTC/EVIC module will send a
beep request to the BCM.
Simultaneously pressing the RESET button and
the STEP button while turning the ignition from
Off to On will enter the CMTC/EVIC into the
self-diagnostic mode.
COMPASS/TEMPERATURE (C/T) BUTTON
Actuating the Compass/Temperature Button
(C/T) will cause the CMTC/EVIC to display the
compass and temperature information. This func-
tion will operate from another traveler display or
from the programmable feature mode.
3.14.2 TRAVELER DISPLAY FUNCTIONS
Using the STEP button will change the CMTC/
EVIC between modes of operation and display the
appropriate information according to data received
from the PCI Bus.
COMPASS/TEMPERATURE
The CMTC/EVIC simultaneously displays the
compass reading and the outside temperature. Out-
side temperature information is received via the
PCI bus from the FCM.
The CMTC/EVIC module internally senses and
calculates the compass direction.
COMPASS OPERATION - ALL
Upon ignition on, if the calibration information
stored in the CMTC memory is within the normal
range, the CMTC will perform in slow Auto-Cal
mode. In slow Auto-Cal mode, the CMTC continu-
ously compensates for the slowly changing mag-
netic field of the vehicle. The compass module
detects changes in the vehicle magnetism and
makes appropriate internal corrections to ensure
proper displayed direction.
However, if the calibration information stored in
the CMTC memory is not within the normal range
at ignition on, the CMTC will enter fast Auto-Cal.
CAL is displayed along with the temperature.
Auto activation of the fast Auto-Cal mode will
also occur when the CMTC is subjected to high
magnetic field strength levels, which cause all com-
pass readings to be erroneous for a continuous
period of five (5) minutes. During fast Auto-Cal,
CAL will be displayed along with the temperature.
Fast Auto-Cal can also be performed manually, by
pressing and holding the RESET button for 10
seconds during the Compass/Temperature display
mode.
3.14.3 SETTING MAGNETIC ZONE
VARIANCE
Variance is the difference between magnetic
North and geographic North. For proper compass
function, the correct variance zone must be set.
Refer to the Zone Variance map for the correct zone.
Follow these steps to check or change the variance
zone:
CMTC/EVIC:
• The ignition switch must be in the On position
and the CMTC/EVIC display must not be blank.
•
If the compass/temperature data is not currently
being displayed, momentarily press and release
the C/T button to display compass/temp informa-
tion.
• Press and hold the RESET button (approximately
5 seconds) until VARIANCE = XX is displayed.
28
GENERAL INFORMATION