Chrysler 300M 1999 Скачать руководство пользователя страница 627

Страница: 627 / 766

TEST 18A

REPAIRING

(

DECKLID RELEASE SOLENOID OUTPUT FAILURE

(

TROUBLE CODE

Perform TEST 1A Before Proceeding

*Perform Verification TEST VER-2A.

**Check connectors - Clean / repair as necessary.

NOTE: FOR LOCATION KEY OFF.

DISCONNECT

OF ALL COMPONENTS.

THE DECKLID RELEASE

START TEST 18A.

SOLENOID HARNESS

CONNECTOR.**

SEE GENERAL INFO 4.0

FIG. 1

WITH AN OHMMETER,

MEASURE BETWEEN

THE RESISTANCE NO REPAIR

THE OPEN

GROUND AND THE

BELOW 5.0 OHMS?

GROUND CIRCUIT.*

GROUND CIRCUIT.

FIG. 1

YES

KEY ON. WITH A TEST

LIGHT CONNECTED TO

IS THE TEST LIGHT

YES

CONTINUE TEST

GROUND, PROBE THE

ILLUMINATED? 18A ON

THE NEXT

DECKLID RELEASE

PAGE.

CONTROL CKT. FIG. 1

WITH THE DRB,

DOES THE TEST

LEAVE THE TEST ACTUATE THE

LIGHT FLASH ON

AND

YES

REPLACE THE

LIGHT CONNECTED. DECKLID RELEASE

OFF AS

THE

DECKLID RELEASE

SWITCH.

SOLENOID IS

SOLENOID.*

ACTUATED?

STOP THE

WITH AN OHMMETER,

REPAIR THE DECKLID

ACTUATION. MEASURE BETWEEN

THE RESISTANCE

YES

RELEASE CONTROL

TURN THE IGNITION

GROUND AND THE

BELOW 5.0 OHMS?

CIRCUIT FOR A SHORT

OFF.

DECKLID RELEASE

TO GROUND. IF OK,

CONTROL CKT. FIG. 1

REPLACE THE J/B.*

CONNECT A JUMPER REMOVE

THE BODY

WIRE BETWEEN GROUND

CONTROL MODULE

AND THE DECKLID

FROM THE JUNCTION

RELEASE CONTROL CKT. BLOCK.

FIG. 1

JUNCTION BLOCK

REPAIR THE OPEN

WITH AN OHMMETER,

20-WAY INTERNAL

IS THE RESISTANCE

DECKLID RELEASE

MEASURE BETWEEN

CONNECTOR CAVITY 8.

BELOW 5.0 OHMS?

CONTROL CIRCUIT.

GROUND AND THE ...

IF OK, REPLACE THE

FIG. 2

JUNCTION BLOCK.*

YES

REPLACE THE BODY
CONTROL MODULE.*

O
O

C
K

S
Y
S

617

Содержание 300M 1999































































































































































































































































































































































































































































































































































































































































































































































































Результаты поиска

Содержание 300M 1999

Отзывы:

Chrysler 300M 1999, Руководство пользователя, Страница: 627 / 766

Результаты поиска

Содержание 300M 1999

Отзывы: