background image

Chart A – Kit Selection Guide

Grill

Disconnect

Hanger

Wall Mount

Portable

Model

Kit

Kit

Kit

Ground Fault

Cart Kit**

STAR-02A-11-F

PCN 111878

NA

NA

STAR-02A-81-F

PCN 111878

PCN 340777

NA

STAR-02A-21-F

PCN 111878

PCN 340785

NA

STAR-02A-71-F

PCN 111878

PCN 340793

NA

STAR-02A-41-F

PCN 111878

PCN 340806

NA

STAR-02A-61-F

PCN 111878

PCN 340814

NA

STAR-05A-81-F

PCN 111894

PCN 340777

PCN 340620

STAR-05A-21-F

PCN 111894

PCN 340785

PCN 340620

STAR-05A-71-F

PCN 111894

PCN 340793

PCN 340620

STAR-05A-41-F

PCN 111894

PCN 340806

PCN 340620

STAR-05A-61-F

PCN 111894

PCN 340662

PCN 340654

PCN 340814

PCN 340620

STAR-06A-83-F

PCN 340638

PCN 340777

PCN 340830

STAR-06A-23-F

PCN 340638

PCN 340785

PCN 340830

STAR-06A-71-F

PCN 340638

PCN 340793

PCN 340830

STAR-06A-43-F

PCN 340638

PCN 340806

PCN 340830

STAR-06A-63-F

PCN 340638

PCN 340814

PCN 340830

STAR-14A-83-F

PCN 340857

PCN 340777

PCN 340849

STAR-14A-23-F

PCN 340857

PCN 340785

PCN 340849

STAR-14A-71-F

PCN 340857

PCN 340793

PCN 340849

STAR-14A-43-F

PCN 340857

PCN 340806

PCN 340849

STAR-14A-63-F

PCN 340857

PCN 340814

PCN 340849

OPTIONAL ACCESSORIES

** Includes Grill(s)

4

MAINTENANCE

ELECRIC SHOCK HAZARD. Disconnect all power
before servicing or replacing heating elements.

BURN HAZARD. Hot surfaces. Allow sufficient time for
heater to cool before serviceing or cleaning heater.

The reflectors should be kept clean to obtain the maximum

radiant output.

Element Replacement
1.

Remove Terminal Box Cover.

2.

Disconnect lead wires from heater terminals and disengage box
from conduit /cable fitting.

3.

Remove safety grills (if installed).

4.

Remove retainer screw located on the reflector at the terminal end.

5.

Loosen (2), 3/8" nuts from the terminal box bracket located on the
back of the heater and slide the entire heating element assembly
out of the reflector assembly.

6.

Remove wires and jumper straps as required to replace the failed
heating element(s).

7.

Remove bulkhead fitting nuts and washers.

8.

Remove failed element and replace with a new element.  Replace
only with genuine Chromalox "Arctic End" elements.  Use of other
elements will cause excess temperatures inside terminal box.

9.

Place gasket on the bulkhead fitting and insert terminals and fit-
tings into the element holes in the terminal box.

10.

Place washers and nuts on bulkhead fittings and tighten.

11.

Replace wiring and jumper straps (see Fig. 1).

12.

Reassemble by following the reverse procedures
(steps 5 through 1).

Отзывы: