Christie J 2.0kW Скачать руководство пользователя страница 86 | Manualshive

Страница: 86 / 94

background image

6-12

J Series 2.0, 2.4, and 3.0kW Service Manual

020-100739-01 Rev. 1 (01-2012)

Section 6: Specifications

6.11.2 Electro-Magnetic Compatibility

Emissions

• FCC CFR47, Part 15, Subpart B, Class A - Unintentional Radiators
• CISPR 22: 2008-09/EN55022: 2006 + A1:2007 Class A - Information Technology Equipment

Immunity

• CISPR 24: 1997 +A1:2001+A2:2002/ EN55024: 1998 +A1:2001 +A2:2003 EMC Requirements - Infor-

mation Technology Equipment

6.11.3 Environmental

The product must conform to:
• EU Directive (2002/95/EC) on the restriction of the use of certain hazardous substances (RoHS) in electrical

and electronic equipment and the applicable official amendment(s).

• EU Regulation (EC) No. 1907/2006 on the registration, evaluation, authorization and restriction of chemicals

(REACH) and the applicable official amendments.

• EU Directive (2002/96/EC) on waste and electrical and electronic equipment (WEEE) and the applicable

official amendment(s).

• China Ministry of Information Industry Order No.39 (02/2006) on the control of pollution caused by elec-

tronic information products, the hazardous substances concentration limits (SJ/T11363-2006), and the appli-
cable product marking requirement (SJ/T11364-2006).

6.11.4 Marking

This product shall conform to all relevant Canadian, US, and European directives, standards, safety, health and
environmental concerns and bears the following markings at product launch:
• UL
• CE
• RoHS
• WEEE
• Future International Certifications to include: CCC, KC, PSE, c-tick, Gost-R, South Africa
• International packaging recycling mark requirements:
• EU Directive (94/62/EC) on packaging and packaging waste;
• China packaging recycling mark standard (GB18455-2001);
• Korea extended producer responsibility (EPR) separate discharge mark system under the act on the promo-

tion of resource saving and recycling (2003);

• United States society of the plastics industry (SPI) resin identification code (1988);
• ISO standards on marking of plastics (11469:2000, 1043-1:2001, 1043-2:2000, 1043-3:1996, and 1043-

4:1998).

«
...
84
85
86
87
88
...
»

Содержание J 2.0kW































































































Отзывы:

Нет отзывов

Похожие инструкции для J 2.0kW

Бренд: M-system Страницы: 3

Бренд: NEC Страницы: 2

PTAE3000U - HOME THEATER LCD PROJECTOR

Бренд: Panasonic Страницы: 60

Бренд: NEC Страницы: 72

SCR-10IN-LCD-1080P-12V

Бренд: Larson Electronics Страницы: 2

COMPACTVIEW CLAN X15-I

Бренд: 3D Perception Страницы: 36

Бренд: Monster Power Страницы: 5

DLA-RS15U - Reference Series Home Cinema Projector

Бренд: JVC Страницы: 18

Бренд: JVC Страницы: 47

Бренд: JVC Страницы: 8

Бренд: JVC Страницы: 12

Бренд: JVC Страницы: 2

Бренд: JVC Страницы: 64

DLA-RS1U - Reference Series Home Cinema Projector

Бренд: JVC Страницы: 1

Бренд: JVC Страницы: 48

Бренд: JVC Страницы: 58

DLA-RS1X - Reference Series Home Cinema Projector

Бренд: JVC Страницы: 51

DLA-S15U - D-ila Projector, 1:1 Fixed Lens

Бренд: JVC Страницы: 118

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды