Christie CP42LH Скачать руководство пользователя страница 10

Страница: 10 / 90

Introduction

CP42LH Service Manual

020-101686-03 Rev. 1 (08-2016)

7. Select one of these options:

8. Tap Next.

Technical support

North and South America: +1-800-221-8025 or

[email protected]

Europe, Middle East, and Africa: +44 (0) 1189 778111 or

[email protected]

Asia Pacific:

[email protected]

Christie Managed Services: +1-800-550-3061 or

[email protected]

Option

Description

Upgrade Different



Components Only

Upgrades system components that are newer or older than
the currently installed version.

ICP Only Force Install

Forces an ICP install regardless of what current version is
installed.

Force Upgrade All

Upgrades all components in the upgrade package.

Factory Install

Removes all configurations and upgrades all components.

Содержание CP42LH



























































































Результаты поиска

Содержание CP42LH

Отзывы:

Похожие инструкции для CP42LH

Бренды по названию

Популярные бренды

Christie CP42LH, Руководство по обслуживанию

Результаты поиска

Содержание CP42LH

Отзывы:

Похожие инструкции для CP42LH

Бренды по названию

Популярные бренды