Christie 599 GS Series Скачать руководство пользователя страница 45

Страница: 45 / 65

Command

Description

Values

NTW+SUB0 <value> Modifies subnet mask settings.

—

NTW+GATE <value>

Modifies gateway settings.

—

NTW + MACO ?

Displays the MAC address settings. (Read-only)

—

Examples

Turn the wireless LAN on:

(NTW+SLCT 1)

Set the MAC address to 00:E0:47:01:02:3C:

(NET+MAC0”00:E0:47:01:02:3C”)

Set the IP address to 192.168.000.001:

(NET+ETH0”192.168.000.001”)

Set the the subnet mask to 255.255.255.000:

(NET+SUB0”255.255.255.000”)

OSD–On Screen Display

Displays or hides the on-screen display.

Commands

Command

Description

Values

OSD <0 | 1>

Enables or disables the on-screen display.

0 = Hides the on-screen display
1 = Displays the on-screen display

OST–OSD Transparency

Changes the transparency of on-screen menus and messages.

Commands

Command

Description

Values

OST <value>

Changes the transparency of the menus and messages. 0 to 90

0 (Default)

Examples

Turn off the transparency:

(OST 0)

Serial API commands

GS Series 599 Serial Commands Technical Reference

020-102403-02 Rev. 1 (04-2017)

Содержание 599 GS Series


































































Результаты поиска

Содержание 599 GS Series

Отзывы:

Похожие инструкции для 599 GS Series

Бренды по названию

Популярные бренды

Christie 599 GS Series, Техническое описание

Результаты поиска

Содержание 599 GS Series

Отзывы:

Похожие инструкции для 599 GS Series

Бренды по названию

Популярные бренды