manualshive.com logo in svg

CHINT Astronergy CHSM60LV-HC, Руководство по установке

Поделиться
Скачать
CHINT Astronergy CHSM60LV-HC Скачать руководство пользователя страница 2

 

 

Chint Solar (Zhejiang) Co.,Ltd. | Add:1335 Bin´an Road, Binjiang District, Hangzhou | P.C: 310053 
Tel: 0086-571-5603 1888 | Fax: 086-571-5603 2316 | Website: http://energy.chint.com/

 

1.  Introduction 

1.1 Purpose 

This  document  provides  detailed  instructions  and  valuable  safety  information  regarding  the 

installation, electrical connection, and maintenance of following Chint Solar Crystalline Photovoltaic 

modules: 

CHSM6610M                CHSM6610M (BL)          CHSM6610M/HV        CHSM60M-HC 

CHSM60M(BL)-HC      CHSM6610P                  CHSM6610P/HV          CHSM60P-HC 

CHSM6612M                CHSM6612M/HV            CHSM72M-HC          CHSM60M/LV-HC 

CHSM6612P                CHSM6612P/HV              CHSM72P-HC          CHSM72M/LV-HC 

All the instructions should be read and understood before installation. The installers should be 

trained and  conform  to  all  safety  precautions  in  this  guide  when  installing  the module. Keep this 

guide in a safe place for further reference. 

1.2 Limitation of Liability 

Because the use of this manual and the conditions or methods of installation, operation, use 

and maintenance of photovoltaic (PV) products are beyond Chint Solar

’s control, Chint Solar does 

not afford the  responsibility and expressly disclaims liability for loss,  damage, or expense arising 

out of or in any way connected with such installation, operation, use or maintenance. Chint Solar 

reserves the right to change the manual without prior notice. 

2.  Codes and Regulations 

The mechanical and electrical installation of PV systems should be performed in accordance 

with  all  applicable  codes,  including  electrical  codes,  building  codes  and  electric  utility 

interconnection requirements. Such requirements may vary for mounting location, such as building 

rooftop or motor vehicle applications. Requirements may also vary with system voltage, and for DC 

or AC application. Contact local authorities for governing regulations. 

3. 

Safety

 

Chint  solar  modules  are  designed  to  meet  the  requirements  of  IEC  61215  and  IEC  61730, 

application class A. Modules rated for use in this application class may be used in system operating 

at greater than 50V DC or 240W, where general contact access is anticipated. Modules qualified for 

Содержание Astronergy CHSM60LV-HC


















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды