Chino KR2000 Скачать руководство пользователя страница 80

Страница: 80 / 136

－

13.10 Network settings

13.10.1 Ethernet settings

・

Proceed from the MENU settings.

・

Move the focus to the setting item using direction key.

・

By pressing the ENTER key on the item for setting, the screen moves to the input screen.

By selecting the network settings on the setting menu screen and then selecting the Ethernet settings, the
following screen is displayed

Set IP address, etc. for using this recorder on the Ethernet.

■

IP address

Set IP address of this recorder. The DHCP (automatic assignment of IP addresses) cannot be used.

Ask the IP address to the administrator for the network to connect.

■

Subnet mask

Set the subnet mask of this recorder.

■

Default gateway

If there is router gateway like a router, etc. on the network, set default gateway address.

When this recorder is used in a small network without connecting to an interoffice LAN or Internet
via a router, set the IP address as follows.

Instrument

IP address

Subnet mask

KR2000 A

192.168.254.254

255.255.255.0

KR2000 B

192.168.254.253

255.255.255.0

…

PC A

192.168.254.1

255.255.255.0

PC B

192.168.254.2

255.255.255.0

…

Example of usage in small scale network

Содержание KR2000









































































































































Результаты поиска

Содержание KR2000

Отзывы:

Chino KR2000, Общее руководство по эксплуатации, Страница: 80 / 136

Результаты поиска

Содержание KR2000

Отзывы: