CHIEF KSA-1022 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 16

CHIEF KSA-1022 Скачать руководство пользователя страница 11

Installation Instructions

KSA-1022

11

Figure 17

9.

Snap off plastic straps on anchor at wall by pushing side to
side, snapping off straps level with flange of plastic cap.
(See Figure 18)

10. Repeat steps 6 through 9 for each mounting hole.

Figure 18

11. Place wall track accessory over anchors and align mounting

holes in display mount with holes in anchors. (See Figure
13)

12. Insert 1/4-20 x 1 3/4" Phillips pan head screws (D) through

corresponding mounting hole on wall track accessory and
into anchor (C) and tighten until flush against mount. DO
NOT overtighten! (See Figure 14)

13. Repeat steps 11 through 12 for remaining mounting holes.

WARNING:

IMPROPER INSTALLATION CAN LEAD TO

EQUIPMENT FALLING CAUSING SERIOUS PERSONAL
INJURY OR DAMAGE TO EQUIPMENT! Overtightening of
mounting hardware can damage the steel studs. DO NOT
overtighten mounting hardware!

Figure 19

Computer Hardware Installation on
Horizontal Bracket

WARNING:

Exceeding the weight capacity can result in

serious personal injury or damage to equipment! It is the
installer’s responsibility to make sure the weight of each
component attached to the KSA-1022 wall track accessory
does not exceed 25 lbs (11.3 kg) or the specific weight limit
for the attached mounting device. Additionally, there is a limit
on how many components may be mounted on each bracket
depending on the mounting method. Refer to the table below
for details.

WARNING:

For horizontal dual stud mounting on wood or

steel studs, a minimum distance of 8" must exist between
mounted devices. For horizontal triple stud mounting on
wood or steel studs, a minimum distance of 14" must exist
between mounted devices. (See Figure 20)

Plastic Cap

Drywall

Anchor Metal Channel

SIDE VIEW

(C) x 4 or 6

8

Steel Stud

Plastic Straps

Drywall

Anchor Metal Channel

Plastic Cap

SIDE VIEW

9

Steel Stud

Two Mount Maximum

Three Mount Maximum

Horizontal, dual stud mounting

Horizontal, triple stud mounting

Vertical, drywall mounting

Vertical, single stud mounting

Drywall

Anchor Metal Channel

Wall Track Accessory

SIDE VIEW

(D) x 4 or 6

9

Steel Stud

«
...
9
10
11
12
13
...
»

Содержание KSA-1022

















Отзывы:

Нет отзывов