FRA
Installation Instructions
2
DISCLAIMER
Milestone AV Technologies and its affiliated corporations and
subsidiaries (collectively “Milestone”), intend to make this
manual accurate and complete. However, Milestone makes no
claim that the information contained herein covers all details,
conditions or variations, nor does it provide for every possible
contingency in connection with the installation or use of this
product. The information contained in this document is subject
to change without notice or obligation of any kind. Milestone
makes no representation of warranty, expressed or implied,
regarding the information contained herein. Milestone assumes
no responsibility for accuracy, completeness or sufficiency of
the information contained in this document.
Chief® is a registered trademark of Milestone AV Technologies.
All rights reserved.
DEFINITIONS
MOUNTING SYSTEM:
A MOUNTING SYSTEM is the
primary Chief product to which an accessory and/or component
is attached.
ACCESSORY:
AN ACCESSORY is the secondary Chief
product which is attached to a primary Chief product, and may
have a component attached or setting on it.
COMPONENT:
A COMPONENT is an audiovisual item
designed to be attached or resting on an accessory or mounting
system such as a video camera, CPU, screen, display,
projector, etc.
WARNING:
A WARNING alerts you to the possibility of
serious injury or death if you do not follow the instructions.
CAUTION:
A CAUTION alerts you to the possibility of
damage or destruction of equipment if you do not follow the
corresponding instructions.
IMPORTANT SAFETY INSTRUCTIONS
WARNING:
Failure to read, thoroughly understand, and
follow all instructions can result in serious personal injury,
damage to equipment, or voiding of factory warranty! It is the
installer’s responsibility to make sure all accessories are
properly assembled and installed using the instructions
provided.
WARNING:
Failure to provide adequate structural strength
for this accessory can result in serious personal injury or
damage to equipment! It is the installer’s responsibility to
make sure the mounting system to which this accessory is
attached can support the combined weight of all equipment.
The wall to which the mounting system and accessory is
being attached may have a maximum drywall thickness of
5/8” (1.6cm).
WARNING:
Exceeding the weight capacity can result in
serious personal injury or damage to equipment! Adding the
FRA accessory may change the weight capacity listed for the
mounting system. Consult (Table 1) for mounting system’s
weight capacity details when attached to the FRA accessory.
Table 1: Weight Capacity When Attached to FRA
WARNING:
Use this accessory only for its intended use as
described in these instructions. Do not use attachments not
recommended by the manufacturer.
WARNING:
Never operate this accessory if it is damaged.
Return the accessory to a service center for examination and
repair.
WARNING:
Do not use this accessory outdoors.
IMPORTANT ! :
The FRA accessory is only compatible with
screens having a VESA pattern, with a maximum of
400mm x 400mm.
IMPORTANT ! :
The FRA accessory is designed to be
mounted to the following Chief mounting systems (mounts
compatible with a 300mm pattern):
--SAVE THESE INSTRUCTIONS--
Mounting System
Mounting System Weight
Capacity with FRA Attached
STMS1U
55 lbs (24.9 kg)
MTMS1U
55 lbs (24.9 kg)
MSM1U
105 lbs (47.6 kg)
LVS1UP
125 lbs (56.7 kg)
LVS1U
125 lbs (56.7 kg)
MCM1U with
FCASFP
105 lbs (47.6 kg)
MFAUB
105 lbs (47.6 kg)
MPAUB
105 lbs (47.6 kg)
MFAUB with
FCASFP
55 lbs (24.9 kg)
MPAUB with
FCASFP
105 lbs (47.6 kg)
•
STMS1U
•
MTMS1U
•
MSM1U
•
LVS1UP
•
LVS1U
•
MCM1U with
FCASFP
•
MFAUB
•
MPAUB
•
MFAUB with
FCASFP
