Chicago Electric 98706 Скачать руководство пользователя страница 8

Страница: 8 / 32

Page 8

for technical questions, please call 1-800-444-3353.

SKU 98706

bAsiC spECifiCATions

Fuel

Type

91+ octane premium

unleaded gasoline

Capacity 4 Gallons

Engine

Oil

Type

SAE 10W-30 above 32°F

SAE 5W-30 at 32°F or below

Capacity 2/3 Quart; Low Oil Shutdown

Sensor

Spark Plug Gap

0.030”

Run Time @

50% Load

9 Hours with full tank

Engine Type

6.5 HP Four-stroke Overhead

Valve Design

Ignition

Recoil Start with Electronic

Ignition

Electrical Outlets

One 20A duplex NEMA

120V~receptacle
One 25A NEMA 120V 3 prong

twist lock receptacle
One T-Type 12V outlet

note:

Additional specifications found

in the TECHNICAL ENGINE

SPECIFICATIONS chart in this

manual.
The emission control system for this

engine is warranted for standards set by

the U.S. Environmental Protection Agency

and by the California Air Resources Board

(also known as CARB). For warranty

information, refer to the last pages of this

manual.

At high altitudes, the engine’s

carburetor, governor (if so equipped), and

any other parts that control the fuel-air

ratio will need to be adjusted by a qualified

mechanic to allow efficient high-altitude

use and to prevent damage to the engine

and any other devices used with this

product.

functions

This unit can power items such as the

following:

iTEM

Running

WATTs

sTART-up

WATTs

Belt Sander

1200

2400

Refrigerator/Freezer

700

2200

1/2 HP Sump Pump

1050

2150

1/2 HP Well Pump

1000

2100

Miter Saw

1650

3000

1-1/2 HP Capacitor Start

& Run Motor

1400

3100

note:

The above wattages are estimates.

Check nameplate wattages on all

loads before connecting to generator.

unpACKing

When unpacking, check to make sure

that the item is intact and undamaged. If

any parts are missing or broken, please

call Harbor Freight Tools at 1-800-444-

3353 as soon as possible.

REMOVE THESE BOLTS AND BRACKETS BEFORE USE!

There are two metal brackets that

secure the generator to the bottom of the

crate. These brackets hold the generator

in place during shipment to prevent

damage. They must be removed before

use.

see the photo above.

REv 08g

Содержание 98706

































Результаты поиска

Содержание 98706

Отзывы:

Похожие инструкции для 98706

Бренды по названию

Популярные бренды

Chicago Electric 98706, Инструкции по установке, эксплуатации и обслуживанию

Результаты поиска

Содержание 98706

Отзывы:

Похожие инструкции для 98706

Бренды по названию

Популярные бренды