background image

SKU 98544 

For technical questions, please call 1-800-444-3353. 

Page 5

Specific Drill/Driver Safety 

Warnings

maintain a safe working environ-

1. 

ment.  

Keep the work area well lit.  

Make sure there is adequate sur-

rounding workspace.  Always keep 

the work area free of obstructions, 

grease, oil, trash, and other debris.  

Do not use the Cordless Drill/Driver 

in areas near flammable chemicals, 

dusts, and vapors.  Do not use this 

product in a damp or wet location.

maintain labels and nameplates on 

2. 

the Cordless Drill/Driver.  

These 

carry important information.  If un-

readable or missing, contact Harbor 

Freight Tools for a replacement.

When using the Cordless Drill/

3. 

Driver, always maintain a firm grip 

on the tool with both hands.
Hold the tool by its insulated grip-

4. 

ping surfaces when performing an 

operation where the Cordless Drill/

Driver may contact hidden wiring.  

Contact with a “live” wire will make 

exposed metal parts of the Cordless 

Drill/Driver “live” and shock the op-

erator.

Do not use the Cordless Drill/

5. 

Driver or Charger if it has been 

dropped, damaged, left outdoors, 

or immersed in liquid.
To avoid electric shock, do not 

6. 

pull or carry the Charger by its 

power Cord or pull the power Cord 

around sharp corners or edges.  

Do not unplug the Charger by pulling 

on the Power Cord.  Keep the Power 

Cord away from heated surfaces.

To avoid electrical shock, do not 

7. 

handle the Charger or the Cordless 

Drill/Driver with wet hands.
Keep the Handles of the Cordless 

8. 

Drill/Driver dry, clean, and free 

from oil or grease.
avoid unintentional starting.  

9. 

Make 

sure you are prepared to begin work 

before turning on the Cordless Drill/

Driver.

never leave the Charger unat-

10. 

tended when it is plugged into an 

electrical outlet.  

Unplug the Char-

ger from its electrical outlet before 

leaving.  Place the Charger on a solid 

surface such as a garage floor; never 

place on anything flammable.

pROpER BaTTERY paCK CaRE: 

11. 

Battery pack (44) leakage may oc-

cur under extreme usage or tem-

perature conditions.  

If Battery Pack 

fluid comes in contact with skin, rinse 

with lemon juice and vinegar then 

wash with soap and water.  If the fluid 

comes into contact with the eyes, 

flush with water for several minutes 

and contact a doctor immediately.  

Never burn the Battery Pack, as it 

can explode in a fire.  Do not charge 

the Cordless Drill/Driver with a leak-

ing Battery Pack.  Contact local solid 

waste authorities for instructions on 

correct disposal or recycling of the 

Battery Pack. 

WaRnIng!  people with pace-

12. 

makers should consult their 

physician(s) before using this 

product.  

Operation of electrical 

equipment in close proximity to a 

heart pacemaker could cause inter-

ference or failure of the pacemaker.

Содержание 98544

















Отзывы: