manualshive.com logo in svg

Chicago Electric 91214, Руководство пользователя и инструкции по безопасности, Страница: 9 / 12

Поделиться
Скачать
Chicago Electric 91214 Скачать руководство пользователя страница 9

Page 9

For technical questions, please call 1-800-444-3353.

Item 91214 

        

Maintenance and Servicing

  Procedures not specifically explained in this manual must 

be performed only by a qualified technician.

TO PREVENT SERIOUS INJURY FROM TOOL FAILURE: 

Do not use damaged equipment.  If abnormal noise or vibration 

occurs, have the problem corrected before further use.

Lens and Helmet Maintenance

Replace the Front Lens Cover if it is damaged 

(cracked, scratched, soiled or pitted).

1. 

To Replace the Cover:

a.  Remove the Front Lens Cover by gently pulling up 

the central part of the Lens -see Figure E, right.

b.  Remove the protection film from both 

sides of the new Lens if it comes with the 

film on.  Place the new Lens into the right 

position by bending it slightly, enough to fit 

in between the tabs at each side of the lens 

and putting the lens in place -see Figure E.

c.  Check and make sure that the 

Lens is securely installed.

2. 

Clean the Filter Lens

 with a clean 

lint-free tissue or cotton cloth.

3. 

Do not immerse

 the lens in water or any other liquid.  

Never use abrasives, solvents or oil based cleaners.

4. 

Do not remove 

the auto-darkening 

filter from the Auto-Darkening Welding 

Helmet.  Never try to open the filter.  

5. 

Storage temperature:  -13 to 167° F.

Figure E

SAFETY

OPERA

TION

MAINTENANCE

SPECIFICA

TIONS

Содержание 91214













Отзывы:

Нет отзывов