background image

Page 13

For technical questions, please call 1-800-444-3353.

Item 69946

SAFET

y

O

PERA

TION

M

AINTENANCE

SETUP

Maintenance and Servicing

  Procedures not specifically explained in this manual must 

be performed only by a qualified technician.

TO PREVENT SERIOUS INJURy FROM ACCIDENTAL OPERATION: 

Turn the Power Switch of the tool off and remove the battery pack before 

performing any inspection, maintenance, or cleaning procedures.
TO PREVENT SERIOUS INJURy FROM TOOL FAILURE: 

Do not use damaged equipment.  If abnormal noise or vibration 

occurs, have the problem corrected before further use.

Cleaning, Maintenance, and Lubrication

1. 

BEFORE EACH USE,

 inspect the general 

condition of the tool.  Check for:
•  loose hardware, 
•  misalignment or binding of moving parts, 
•  cracked or broken parts, 
•  damaged electrical wiring, and 
•  any other condition that may 

affect its safe operation.

2. 

AFTER USE,

 wipe external surfaces 

of the tool with clean cloth.

3.  Protect the tool and its parts and 

accessories from moisture and humidity.

4.  Some of the bits provided are “grinding bits” 

using stone abrasives.  During use, these 

may clog up with removed material or 

lose their shape.  To clean and reshape 

these bits, run them against the provided 

Dressing Stone. The Dressing Stone will 

abrade away the clogging materials and will 

reshape the Grinding Bits as appropriate.

5.  NiCd BATTERY MUST BE RECYCLED 

OR DISPOSED OF PROPERLY.  

Do not short, incinerate or open battery.

6.  Dispose of used batteries properly. 

Consult your local hazardous waste 

authority for disposal guidelines.

7.  To change the batteries in the LED Collar:

a. Remove it from the Rotary Tool.

b. Using a cross head screwdriver, open the 

battery compartment.

c. Replace the batteries with the same type as 

originally installed (Two CR-927, 3V 

batteries). Be sure to match the polarity 

marking in the battery compartment.

Содержание 69946

















Отзывы: