Chicago Electric 69924 Скачать руководство пользователя страница 9

Страница: 9 / 16

Page 9

For technical questions, please call 1-800-444-3353.

Item 69924

Specifications

Electrical Rating

120V~ / 60Hz / 5.7A

No Load Speed

6,400 OPM

Spindle Thread

5/16″ - 24 UNF

Max. Accessory Diameter 6″ (150mm)

Setup - Before Use:

Read the ENTIRE IMPORTANT SAFETY INFORMATION section at the beginning of this

manual including all text under subheadings therein before set up or use of this product.

TO PREVENT SERIOUS INJURY FROM ACCIDENTAL OPERATION:

Make sure that the Power Switch is in the off-position and unplug the tool from

its electrical outlet before performing any procedure in this section.

Note:

For additional information regarding the parts listed in the following pages,

refer to the Assembly Diagram near the end of this manual.

ASSEMBLY
Installing the Side Handle

TO PREVENT SERIOUS INJURY:

Do not operate this tool with one hand only or without the Side Handle properly installed.

1. The Side Handle may be installed in one of two

positions, on either side of the Gear Housing.

2. Screw the threaded end of the

Side Handle into the selected position.

Tighten securely before beginning work.

Functions

Backing

Pad (47)

Pad Connector (46)

hidden under Shroud

Switch (21)

Side Handle (30)

Speed

Control (20)

SAFETY

OPERA

TION

MAINTENANCE

SETUP

Содержание 69924

















Результаты поиска

Содержание 69924

Отзывы:

Похожие инструкции для 69924

Бренды по названию

Популярные бренды

Chicago Electric 69924, Руководство пользователя

Результаты поиска

Содержание 69924

Отзывы:

Похожие инструкции для 69924

Бренды по названию

Популярные бренды