background image

Page 7

For technical questions, please call 1‑800‑444‑3353.

Item 68012 

        

SAFET

y

Op

ERA

TION

M

AINTENAN

c

E

SETU

p

Specifications

Charger Input Rating

120V~ / 60Hz

Battery Rating

12V / 1300mAh

Battery Type

Li-ion

No Load Speed

10,000-18,000 OPM

Accessories

Hex Key

Setup ‑ Before Use:

Read the ENTIRE IMpORTANT SAFETy INFORMATION section at the beginning of this 

manual including all text under subheadings therein before set up or use of this product.

Note:

 For additional information regarding the parts listed in the following pages, 

refer to 

Parts List and Diagram

 on page 11.

Functions

Speed control Knob 

power Switch

Sanding pad

Battery pack

Note:

  Sanding Pad sold separately.

Figure A

charger Indicator LED’s

1.  The green LED lights once Charger is plugged in.

2.  The red LED will light during charging.

3.  When Battery Pack is fully charged,  

both red and green LED’s will stay lit.

4.  If both red and green LED’s flash, the charger and/or  

battery are not functioning properly.  Stop charging 

immediately and contact a qualified technician.

Green LED

Red LED

Figure B 

Содержание 68012













Отзывы: