background image

Page 4

For technical questions, please call 1-800-444-3353.

SKU 66619 

        

oPERATING PREcAUTIoNS

1. 

cARboN MoNoXIDE 

hAzARD 

Using a generator indoors 

cAN KIll YoU IN MINUTES. 

Generator exhaust contains 

carbon monoxide.  This is a poison you 

cannot see or smell. 

NEVER use inside a home or garage, 

EVEN IF doors and windows are open. 

Only use OUTSIDE and far away from 

windows, doors, and vents.
Keep all safety guards in place and in 

2. 

proper working order at all times.

NEVER place fingers, hands, or body 

3. 

near the Generator when it is running.  

Do not lean or reach over the Generator 

when the machine is running.
Keep all people (except the operator) a 

4. 

minimum of six feet from the Generator 

during operation.
Do not transport the Generator with the 

5. 

Engine running.
Do not sit or stand on this machine.

6. 

Do not tilt the machine while the Engine 

7. 

is running.
Do not leave the Generator unattended 

8. 

when it is running.  Turn off the Engine 

before leaving the area.

Wear ANSI-approved safety goggles, 

9. 

hearing protection, and heavy duty work 

gloves during use.
People with pacemakers should 

10. 

consult their physician(s) before use.  

Electromagnetic fields in close proximity 

to a heart pacemaker could cause 

pacemaker  interference or pacemaker 

failure.  Caution is necessary when near 

the engine’s magneto or recoil starter.
Use only accessories that are 

11. 

recommended by Harbor Freight Tools 

for your model.  Accessories that may 

be suitable for one piece of equipment 

may become hazardous when used on 

another piece of equipment.
Do not operate in explosive 

12. 

atmospheres, such as in the presence 

of flammable liquids, gases, or dust.  

Gasoline-powered engines may ignite 

the dust or fumes.
Stay alert, watch what you are doing 

13. 

and use common sense when operating 

this piece of equipment.  Do not use 

this piece of equipment while tired or 

under the influence of drugs, alcohol or 

medication.
Do not overreach.  Keep proper footing 

14. 

and balance at all times.  This enables 

better control of the equipment in 

unexpected situations.
Dress properly.  Do not wear loose 

15. 

clothing or jewelry.  Keep hair, clothing 

and gloves away from moving parts.  

Loose clothes, jewelry or long hair can 

be caught in moving parts.
Parts, especially exhaust system 

16. 

components, get very hot during use.  

Stay clear of hot parts.
Do not cover the Generator during 

17. 

operation.

REv 10b

Содержание 66619


























Отзывы: