Chicago Electric 60373 Скачать руководство пользователя страница 30 | Manualshive

Страница: 30 / 40

Chicago Electric 60373 Скачать руководство пользователя страница 30

Page 10

For technical questions, please call 1-888-866-5797.

Item 60373

Extension Cords

1.

Grounded

tools require a three wire extension cord.

Double Insulated

tools can use either

a two or three wire extension cord.

2. As the distance from the supply outlet increases,

you must use a heavier gauge extension cord.
Using extension cords with inadequately sized wire
causes a serious drop in voltage, resulting in loss of
power and possible tool damage.

(See Table A.)

3. The smaller the gauge number of the wire, the

greater the capacity of the cord. For example,
a 14 gauge cord can carry a higher current
than a 16 gauge cord.

(See Table A.)

4. When using more than one extension cord

to make up the total length, make sure
each cord contains at least the minimum
wire size required.

(See Table A.)

5. If you are using one extension cord for more

than one tool, add the nameplate

amperes

and use the sum to determine the required
minimum cord size.

(See Table A.)

6. If you are using an extension cord outdoors, make

sure it is marked with the suffix “W-A” (“W” in
Canada) to indicate it is acceptable for outdoor use.

7. Make sure the extension cord is properly wired

and in good electrical condition. Always replace
a damaged extension cord or have it repaired
by a qualified electrician before using it.

8. Protect the extension cords from sharp objects,

excessive heat, and damp or wet areas.

RECOMMENDED MINIMUM WIRE GAUGE

FOR EXTENSION CORDS*

(120/240 VOLT)

NAMEPLATE

AMPERES

(at full load)

EXTENSION CORD

LENGTH

25′

50′

75′ 100′ 150′

0 – 2.0

18

18

18

18

16

2.1 – 3.4

18

18

18

16

14

3.5 – 5.0

18

18

16

14

12

5.1 – 7.0

18

16

14

12

12

7.1 – 12.0

18

14

12

10

-

12.1 – 16.0

14

12

10

-

-

16.1 – 20.0

12

10

-

-

-

TABLE A

* Based on limiting the line volt-

age drop to five volts at 150% of

the rated amperes.

Symbology

Double Insulated

Canadian Standards Association

Underwriters Laboratories, Inc.

VAC

Volts Alternating Current

A

Amperes

n0 xxxx/min.

No Load Revolutions per Minute (RPM)

WARNING marking concerning Risk
of Eye Injury. Wear ANSI-approved
safety goggles with side shields.

Read the manual before
set-up and/or use.

WARNING marking concerning
Risk of Hearing Loss.
Wear hearing protection.
WARNING marking
concerning Risk of Fire.
Do not cover ventilation ducts.
Keep flammable objects away.
WARNING marking concerning
Risk of Electric Shock.
Properly connect power cord
to appropriate outlet.

SAFETY

OPERA

TION

MAINTENANCE

SETUP

«
...
28
29
30
31
32
...
»

Содержание 60373









































Отзывы:

Нет отзывов