background image

Page 12

SKU 46055

NOTE: Some parts are listed and shown for illustration purposes only and are not available
individually as replacement parts.

PLEASE READ THE FOLLOWING CAREFULLY

THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS
MANUAL AS A REFERENCE TOOL ONLY.  NEITHER THE MANUFACTURER NOR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR
SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS
QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT.  IN FACT, THE MANUFACTURER
AND/OR DISTRIBUTOR EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS
SHOULD BE UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE
BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER
REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING
OUT OF HIS OR HER INSTALLATION OF REPLACEMENT PARTS THERETO.

Part No.

Description

Part No.

Description

1

Speed Control

18

Slide Holder

2

Switch

19

Slide Rod

3

Screw

20

Felt

4

Right Housing

21

Blade Clamp

5

Cord Clip

22

Screw

6

Screw

23

Guard

7

Cord Guard

24

Guide Roller

8

Power Cord

25

Bottom Board

9

Stator

26

Square Nut

10

Bearing

27

Left Housing

11

Brush Holder w/Carbon Brush

28

Nameplate

12

Rotor

29

Washer Board

13

Bearing

30

Spring Washer

14

Center Support

31

Screw

15

Washer

32

Hex Spanner

16

Gear

33

Saw Blade

17

Guide Case

Parts List

Содержание 46055














Отзывы: