Chicago Dryer Edge MAXX Скачать руководство пользователя

Страница: 21 / 288

Edge MAXX

Installation

2-3

2.2 Installation

Procedures

Installation of the unit includes:

Inspection
Uncrating and General Placement
Input Conveyor Installation
Compressed Air Supply Connection
Final Positioning/Easi-Glide Preparation

(Option)
Reject Conveyor Positioning
Electrical Connection

Inspection

Carefully inspect all shipments before they

are accepted from the carrier. Upon delivery,

make sure all items listed on the bill have been

received.

Any shortage, breakage, or damage noticed at

the time of delivery should be indicated on the

carrier’s freight bill and signed by the driver or

carrier’s representative.

Damage noticed after delivery should be

reported to the carrier at once. Request their

inspection of the shipment and ﬁll out a concealed

damage inspection report.

NOTE:

N o t i f y t h e c a r r i e r

immediately if any damage has

been done to the unit during

shipment.

•
•
•
•
•

•
•

Compressed air that is clean and dry must

be provided for the unit. This is very important

because the air will blow directly on the ﬂatwork.

The compressed air supply must meet the

pressure and air ﬂow requirements noted in the

APPENDIX

Technical Speciﬁcations

The electrical requirements of the spreader/

feeder are shown on the nameplate, located on

the back of the right endframe (Figure 2-2).

Additional information can be found in the

APPENDIX

Technical Speciﬁcations

Wiring and a separate, fused disconnect

switch of suitable size must be locally supplied

if local codes require one. Check local codes for

clearance requirements to any electrical box.

Figure 2-2: The nameplate provides information

on the unit’s electrical requirements.

TOC

INDEX

Содержание Edge MAXX

































































































































































































































































































Результаты поиска

Содержание Edge MAXX

Отзывы:

Похожие инструкции для Edge MAXX

Бренды по названию

Популярные бренды

Chicago Dryer Edge MAXX, Инструкция по эксплуатации

Результаты поиска

Содержание Edge MAXX

Отзывы:

Похожие инструкции для Edge MAXX

Бренды по названию

Популярные бренды