Chicago Dryer Edge MAXX Скачать руководство пользователя

Страница: 114 / 288

Troubleshooting

Edge MAXX

6-12

WARNING

Only trained personnel with experience

in electrical or mechanical repair should

troubleshoot and repair the unit.

Troubleshooting

WARNING

Read the

REPAIR

chapter and make

sure that the power is disconnected

before doing any repairs.

ISSUE

POSSIBLE CAUSE

SOLUTION

(continued from previous page)

Unit Starts, Then Shuts Down

(continued from previous

page)

1. Control latching circuit

(hold) is defective.

If message stays displayed:

Close all safety switches.
Press the START button and make

sure the momentary indicator does

not light at all, even for 1-2 seconds.

If indicator lamp lights for 1-2 seconds

while the machine is running, see next

cause.

•

-
-

2. CHI Panel faulty.

Check P01 wiring to CHI Panel.

Check CHI Panel output.

If necessary, replace CHI Panel.

•

Unit Starts, Blank Message

Screen

1. No voltage at the CHI

panel.

Check and repair the 5vdc connection

from the main control board to the CHI

panel.

•

2. The CHI panel is faulty.

Check and repair controller and CHI

panel connections. Check vacuum

tube (vf display) for damage.

Check and repair processor pin con-

nections.

Replace as necessary.

•

Unit Is Running Normally Then

Goes into Standby State

Unit Starts and Goes Immedi-

ately Into Standby State

Message reads:

IRONER/FOLDER NOT READY

1. The spreader/feeder has

received a fault signal

from another machine in

the line.

Make sure communications cable con-

nections between units in the line are

secure.

Determine which machine in the line

caused the fault signal and correct.

•

TOC

INDEX

Содержание Edge MAXX

































































































































































































































































































Результаты поиска

Содержание Edge MAXX

Отзывы:

Похожие инструкции для Edge MAXX

Бренды по названию

Популярные бренды

Chicago Dryer Edge MAXX, Инструкция по эксплуатации

Результаты поиска

Содержание Edge MAXX

Отзывы:

Похожие инструкции для Edge MAXX

Бренды по названию

Популярные бренды