background image

When you’ve completed all the preparation steps, you’re 
ready to install your range hood.

How to Install Your Range Hood

UC-PS38 USER MANUAL

7

1. Power the Range Hood

Power the range hood and test all functions before proceed-
ing with the installation. Plug the power cord into an outlet 
and ensure that the light, fan, and clock work properly. Refer 
to page 9,“How to Use Your Range Hood,” for instruction.

     IMPORTANT:

 

If the range hood is not working properly, 

please contact us immediately (1-800-929-0168 / 
[email protected]).

5. Screw It Into Place

From the bottom of the hood, carefully insert the mount-
ing screws (AA) with washers into each of the pre-drilled 
mounting holes in the range hood. Start with the front left, 
then front right. 
After the screws are in place for the front mounting holes, 
work on the rear left, then rear right. If you feel that you 
need to install the range hood more securely, you can use 
the additional two mounting screw holes in the front/cen-
ter. 

     IMPORTANT:

 

Ensure the hood is perfectly leveled from 

back to front for the water cleaning process to function 
properly.

Tip: To easily reach the rear mounting holes, use an 
extension tool for the power drill.

4. Jack Up the Hood

For this step, you will need one or two helpers. 
If you aren’t removing the range, place the plywood (30” x 
24”) over the range / cooktop to avoid possible damage. Put 
the cabinet jacks on the plywood and place the second piece 
of plywood over the two cabinet jacks. Using the cabinet 
jacks, lift the hood into its position under the cabinet. One 
person should operate the jack while another person steadies 
the range hood and situates it into the proper position. For 
cabinet jack operation, please refer to its manual. 
Ensure that the adapter and power cord enter the cabinet 
openings and that the power cord is not pinched between the 
hood and the cabinet. 
If you don’t use a cabinet jack, you will need three people. 
Have two helpers holding the range hood in place while the 
third person inserts the screws to mount the range hood.

2. Take Off the Panel Filter

Disengage the panel filter from the UC-PS38 range hood by 
putting slight pressure in pulling it down, then slowly lift the 
panel upward and remove gently from the bracket at the 
back.

3. Remove Bottom Cover & Attach the Adapter

Remove the bottom cover by carefully unscrewing the three 
screws as shown. Place the rubber gasket in the opening.
Then, attach a round 6” outlet adapter and securely fasten the 
adapter with two screws.

Screws

AA

Содержание UC-PS38SS-30













Отзывы: