Checkline TI-25SX Скачать руководство пользователя страница 21

– 20 –

9.0  WARRANTY 

ELECTROMATIC Equipment Co., Inc. (ELECTROMATIC) warrants to the original 
purchaser that this product is of merchantable quality and confirms in kind and 
quality with the descriptions and specifications thereof. Product failure or malfunction 
arising out of any defect in workmanship or material in the product existing at 
the time of delivery thereof which manifests itself within one year from the sale 
of such product, shall be remedied by repair or replacement of such product, at 
ELECTROMATIC’s option, except where unauthorized repair, disassembly, tampering, 
abuse or misapplication has taken place, as determined by ELECTROMATIC. All 
returnsfor warranty or non-warranty repairs and/or replacement must be authorized by 
ELECTROMATIC, in advance, with all repacking and shipping expenses to the address 
below to be borne by the purchaser.

THE FOREGOING WARRANTY IS IN LIEU OF ALL OTHER WARRANTIES, 
EXPRESSED OR IMPLIED, INCLUDING BUT NOT LIMITED TO, THE 
WARRANTY OF MERCHANTABILITY AND FITNESS FOR ANY PARTICULAR 
PURPOSE OR APPLICATION. ELECTROMATIC SHALL NOT BE RESPONSIBLE 
NOR LIABLE FOR ANY CONSEQUENTIAL DAMAGE, OF ANY KIND OR 
NATURE, RESULTING FROM THE USE OF SUPPLIED EQUIPMENT, WHETHER 
SUCH DAMAGE OCCURS OR IS DISCOVERED BEFORE, UPON OR AFTER 
REPLACEMENT OR REPAIR, AND WHETHER OR NOT SUCH DAMAGE IS 
CAUSED BY MANUFACTURER’S OR SUPPLIER’S NEGLIGENCE WITHIN ONE 
YEAR FROM INVOICE DATE.

Some State jurisdictions or States do not allow the exclusion or limitation of incidental 
or consequential damages, so the above limitation may not apply to you. The duration 
of any implied warranty, including, without limitation, fitness for any particular 
purpose and merchantability with respect to this product, is limited to the duration of 
the foregoing warranty. Some states do not allow limitations on how long an implied 
warranty lasts but, not withstanding, this warranty, in the absence of such limitations, 
shall extend for one year from the date of invoice.

ELECTROMATIC Equipment Co., Inc. 

 

 

 

 

600 Oakland Ave. Cedarhurst, NY 11516—USA 

 

 

 

Tel: 1-800-645-4330/ Tel: 516-295-4300/ Fax: 516-295-4399 

Every precaution has been taken in the preparation of this manual. Electromatic Equipment Co., Inc., assumes 
no responsibility for errors or omissions. Neither is any liability assumed for damages resulting from the use of 
information contained herein. Any brand or product names mentioned herein are used for identification purposes 
only, and are trademarks or registered trademarks of their respective holders

Содержание TI-25SX























Отзывы: