background image

1. B

EFORE

Y

OU

B

EGIN

What is included 

¾

 

1 x SX Gobo™ 

¾

 

EHJ 24V 250W Lamp 

¾

 

7 Replaceable Gobos 

¾

 Warranty 

Card 

¾

 User 

Manual 

Unpacking Instructions 

Immediately upon receiving a fixture, carefully unpack the carton, check the contents to ensure that 

all parts are present, and have been received in good condition. Notify the shipper immediately and 

retain packing material for inspection if any parts appear damaged from shipping or the carton itself 

shows signs of mishandling. Save the carton and all packing materials. In the event that a fixture 

must be returned to the factory, it is important that the fixture be returned in the original factory box 

and packing. 

AC Power 

To determine the power requirements for a particular fixture, see the label affixed to the back plate of 

the fixture or refer to the fixture’s specifications chart. A fixture’s listed current rating is its average 

current draw under normal conditions. All fixtures must be powered directly off a switched circuit and 

cannot be run off a rheostat (variable resistor) or dimmer circuit, even if the rheostat or dimmer 

channel is used solely for a 0% to 100% switch. Before applying power to a fixture, check that the 

source voltage matches the fixture’s requirement.  

Warning! 

Verify that the voltage required by your unit matches the line voltage applied. 
Damage to your fixture may result if the line voltage applied does not match the 
voltage required by the fixture. All fixtures must be connected to circuits with a 
suitable Earth Ground.  

Contact Us 

W o r l d   W i d e  

General Information

Chauvet Lighting 
3000 North 29

th

 Court 

Hollywood, FL 33020 
voice: 954.929.1115 
fax: 954.929.5560 
toll free:  800.762.1084 

Technical Support

Chauvet Lighting 
3000 North 29

th

 Court 

Hollywood, FL 33020 
voice: 954.929.1115

 (Press 4)

fax: 954.929.5560

 (Attention: Service)

World Wide Web 

www.chauvetlighting.com

SX Gobo Manual 

3

2006-12-11/15:16

Содержание SX Gobo













Отзывы: