Chauvet Arena Hazer 3 Скачать руководство пользователя страница 4

 
 
 
 

Page 4 of 16 

Arena™ Hazer 3 User Manual (Rev. 02) 

Product at a Glance 

 

 

Use on Dimmer 

Auto Programs 

 

Outdoor Use 

Auto-ranging Power Supply 

 

Sound Activated 

 

Replaceable Fuse 

 

DMX 

User Serviceable 

 

 

Master/Slave 

Duty Cycle 

 

Safety Notes 

 

 

Please read the following notes carefully before starting to work with this 
product. They include important safety information about its installation, usage, 
and maintenance. 

 

 

  Keep this User Manual for future consultation. If you sell this product to another 

user, be sure that they also receive this document. 

  Always make sure that the voltage of the outlet to which you are connecting this 

product is within the range stated on the decal or rear panel of the fixture. 

  This product is for indoor use only! To prevent risk of fire or shock, do not expose 

this fixture to rain or moisture. 

  Make sure there are no flammable materials close to the unit while operating. 

  Always install this product in a location with adequate ventilation, at least 20 in (50 

cm) from adjacent surfaces.  

  Be sure that no ventilation slots on the unit’s housing are blocked. 

  Always disconnect this product from the power source before cleaning it or 

replacing fuse. 

  Make sure to replace the fuse with another of the same type and rating. 

  The maximum ambient temperature (Ta) is 104° F (40° C). Do not operate this 

product at higher temperatures.  

  In the event of a serious operating problem, stop using the unit immediately.  

  Never try to repair this product. Repairs carried out by unskilled people can lead 

to damage or malfunction. Please contact the nearest authorized technical 
assistance center. 

  Never connect this product to a dimmer pack. 

  Make sure the power cord is not crimped or damaged. 

  Never disconnect the power cord by pulling or tugging on the cord. 

  Never carry a fixture from the power cord or any moving part. Always use the 

hanging/mounting bracket or the handles. 

  Always avoid direct eye exposure to the light source when this fixture is on. 

  Do not touch the output nozzle on this product. It is very hot during operation and 

it may remain hot for several hours after turning the unit off. 

  Do not mount this product on a flammable surface (e.g., wood, linoleum, carton, 

plastic, or carpet).  

  Make sure there are no flammable materials close to the unit while operating. 

  Depending on the amount of fog/haze generated, all fog machines may set off 

smoke detectors. 

 

 

 

FCQ (Fog Cleaner Quart) was specifically developed by Chauvet to clean your 
Arena™ Hazer 3. Make sure you use FCQ regularly to increase the life of your 
product. 

 

 

Содержание Arena Hazer 3

















Отзывы: