Charter Spectrum D3.1 eMTA Скачать руководство пользователя страница 2

 Spectrum D3.1 eMTA Quick Installation Guide 

 

 

 

1

 

• 

SAFETY NOTICES 

Device Grounding:

 Install the cable modem to include grounding the coaxial cable 

to the earth as close as practical to the building entrance per ANSI/NFPA 70 and 

the National Electrical Code (NEC, in particular, Section 820.93, Grounding of the 

Outer Conductive Shield of a Coaxial Cable). The device is designed for IT power 

systems with phase-to-phase voltage at 120V.  

This unit requires a 100-240V, 50-60Hz power adapter. The power adapter must 

be keyed for proper polarization, and must be fully inserted to contact the back 

of the power connector port to ensure snug connection. Use only the supplied 

power adapter.  

Disconnecting the Device:

  

If the cable modem becomes damaged or encounters 

some other abnormality, disconnect the power adapter from the AC wall outlet 

immediately.  

Temperature and Altitude:

 

Install the device in a location not to exceed the 

maximum operating temperature of 104˚F (40˚C). Maximum operating altitude is 

5000 m (16,404 ft.). 

• 

PREPARING FOR INSTALLATION 

Verify package contents, RF cable connectors, and power outlet. 

 

Unpack the 

box and confirm the following components: 

 

 

Locate the RF (coaxial) cable connector on the wall. 

 

Verify the power outlet 

is working and is wired correctly.  Place your cable modem within a proper 
distance from the outlet. 

• 

BASIC MODEM INFORMATION 

Example of Cable RF 

MAC Address

 

00:71:CC:8E:54:C7

 

Firmware Version

 

14.1.2xxx

 

Compatibility

 

DOCSIS 3.1/3.0/2.0/1.0 certified Ethernet 

10/100/1000 Mbps

 

Local Web 

 

User Interface 

 

Access

 

http://192.168.100.1

 

Modem Web 

 

Page Login (web user 

interface)

 

Login: technician 

 

Password: C0nf1gur3Ubee#

 

• 

UNDERSTANDING DEVICE CONNECTIONS 

REAR PANEL: 

 

Ethernet (Internet): 

Connect to an Ethernet-enabled device such as a computer, 

gaming console or a wireless access point (LAN switch, router) using an RJ45 

Ethernet cable.  

Voice 1-2:

  Use to connect analog telephones to the device. Telephone service 

must be enabled by your service provider.  

Cable:

 Use to connect to the coaxial cable from your Internet service provider.  

 

 

 

 

 

   

 

 

 

 

 

  

Содержание Spectrum D3.1 eMTA













Отзывы: