Charles Fiber Pedlock BDO2 Series Скачать руководство пользователя страница 21

Страница: 21 / 22

LT-BDO20X-801

Printing

Page 21 of 22

3.4.8.

Splicing Fibers at the BDO2 Pedestal

Step

Number

Description

Prepare to splice fibers and review cautions and warning listed before at the beginning of this document.

After removing the outer dome, loosen the Velcro

straps and remove the tray from the organizer.
Detach the cover by pulling up on the two cover
holes.

Perform splicing per company practice and coil/wrap the fibers following the tray manufacturer’s recommended procedures.

Note: First install the spliced fibers and then the expressed fibers. This will permit access to the fibers that were not spl iced for

future additions, rework or test without disturbing the working fibers.

Per company practice, install the tray label and identify the splices. To replace the cover, first insert it under the tabs o n one side

of the tray. Then flex the tray using one of the holes in the cover, and slide the cover under the remaining tabs. Perform this at
both ends.

Note: Do not push the splice tray cover on top of the tabs, as the tabs may bend. If a tab becomes bent, it can be straighten ed

with a small screw driver or l

ineman’s knife.

Coil all buffer tube slack attached to the tray into the basket. Rest the tray against the tabs on the edge of the basket and secure

the tray with the supplied Velcro straps.

To allow proper dome placement, verify all cabling/tubing is neat and not kinked and verify no cables, cable ties, or tubes

protrude beyond the fiber organizer walls.

Lower the dome and rotate it so that the lock lines up with the base latch. Push down on the dome to activate the locking

mechanism. Verify that the dome is securely attached by pulling up on it after the latch clicks into position.

Содержание Fiber Pedlock BDO2 Series























Результаты поиска

Содержание Fiber Pedlock BDO2 Series

Отзывы:

Бренды по названию

Популярные бренды

Charles Fiber Pedlock BDO2 Series, Общее описание и установка

Результаты поиска

Содержание Fiber Pedlock BDO2 Series

Отзывы:

Бренды по названию

Популярные бренды