background image

GRILL MAINTENANCE

Frequency of clean up is determined by how often the grill is used. Make sure coals are completely extinguished  before 
cleaning inside of the unit. Thoroughly rinse with water and allow to air dry before using again. Wipe out the interior of the 
unit with a cloth or paper towels.

When finished cooking, and the unit has adequately cooled, clean out all remaining ashes. Ashes collect moisture, which 
can lead to premature rusting and decay. Periodically coating the interior surfaces with vegetable oil will aid in the protection 
of your unit. Also, occasional touch up of the exterior paint will be required. Black, high-temperature spray paint is 
recommended. NEVER PAINT THE INTERIOR OF THE UNIT.

Cooking Surface:

 If a bristle brush is used to clean any of the grill cooking surfaces, ensure no loose bristles remain on 

cooking surfaces prior to grilling. It is not recommended to clean cooking surfaces while grill is hot.

PREPARING TO USE THE CHARCOAL SIDE OF YOUR GRILL

Before cooking with your grill, the following steps should be closely followed to both cure the finish and season the interior 
steel. Failure to properly follow these steps may damage the finish and/or impart metallic flavors to your first foods.

?

Brush all interior surfaces including grills and grates with vegetable cooking oil.

?

Build a small fire on the charcoal pan, being sure not to lay coals against the walls.
Close lid, position butterfly dampers at approximately one quarter turn open. This burn should be sustained for at least 

two hours. Begin increasing the temperature by opening the butterfly dampers halfway and adding more charcoal. Your 
grill is now ready for use. 

Rust can appear on the inside of your grill. Maintaining a light coat of vegetable oil on the interior surfaces will aid in the 
protection of your grill. Exterior surfaces of the grill may need occasional touch up. We recommend the use of commercially 
available black high temperature spray paint. NEVER PAINT THE INTERIOR OF THE GRILL!

?

GRILLING

Charcoal is recommended, however, wood or a combination of both may be used as the fuel source for grilling with the fuel 
source placed and ignited on the charcoal pan. Do not build too large of a fire. We recommend starting a fire with no more 
than 2 pounds of charcoal (approximately 30 briquettes) and adding more as needed during cooking. After allowing the fire 
to burn down, place the cooking grate on the unit. Failure to read and follow instructions for lighting charcoal may result in 
serious personal injury and/or property damage. 

Please see information regarding Uncoated Cast Iron Grates and Cooking Tools below.

First Time Use:

Before using a cast iron grate or other cast iron cooking tool, wash it thoroughly with a mild dishwashing liquid to remove the 
protective wax coating applied for shipping. Rinse with hot water and dry completely with a soft cloth or paper towel. NEVER 
ALLOW TO DRAIN DRY OR WASH IN A DISHWASHER. Now season the grates to prevent rust and sticking.

Seasoning:

A solid vegetable shortening is recommended for the initial seasoning. Spread a thin coating of solid vegetable shortening 
over the entire surface, including all corners, with a paper towel. Do not use salted fats such as butter or margarine.
Preheat grill for 15 minutes; carefully place grates in the grill. Allow the grill to heat grates for 1 to 1 ½ hours. Allow the fire to 
burn out on its own, and leave cooking grates in grill until they are cool. Your cast iron cooking grates are now ready to use.

To Prevent Rusting:

Re-season your grates frequently, particularly when new. If rust occurs, it is an indication that the grates have not been 
seasoned enough or the seasoning has been burned off. Clean with a heavy brush like Char-Broil’s Brush Hawg. Reapply 
vegetable shortening and heat as indicated above to re-season the grates.

Maintenance:

Do not do a burn-off after you grill, but rather leave the cooking residues on the grates to keep a protective coating on the 
cast iron. Do a burn-off just before you grill. The more you use your cast iron grates, the easier the maintenance will be.
Store in a dry place. If you store your grates for an extended period of time, grease very lightly with vegetable shortening, 
then wipe dry with a paper towel.
 

CHARCOAL GRILL - PREPARATION

Page 4

Содержание 463724511





































Отзывы:

Похожие инструкции для 463724511