Char-Broil 463721111 Скачать руководство пользователя страница 12

12    

CAUTION

If burner does not light, turn knobs to OFF, wait 5 
minutes, and try again. Always close valve during the 5 
minute waiting period. If the burner does not ignite with 
the valve open, gas will continue to flow out of the burner 
and could accidentally ignite with risk of injury.

Burner Flame Check

•  

Light burner,

Remove cooking grates and flametamers. 

a smaller flame in

 LOW

 position than seen on 

HI

. Always 

check flame prior to each use. If only low flame is seen refer to 
"Sudden drop or low flame" in the 

Troubleshooting Section

.

HI

LOW

Match-Lighting

s

 Do not lean over grill while lighting.

3.  Open lid during lighting.  
4.  

Place match into match holder (hanging from side of cart).

5.  

Place lit match through the match light hole and near the burner.

6. 

Light right burner by pushing knob in and turning to the 

HI 

position.

Hose Check

•  

Before each use, check to see if hoses are cut, worn or kinked. 

Replace damaged hoses before using grill. Use only 
valve/hose/regulator specified in the Parts List.

Normal
Hose

Kinked
Hose

Sideburner Match Lighting

1.
2.

Hold lit match to any port on the burner. Push in and turn 
sideburner knob to the 

HI

 position. 

Turn 

ON

 gas at LP cylinder.

Ignitor Lighting

s

 

 Do not lean over grill while lighting.

1.
2.
3.
4.
5.

Turn 

OFF

 gas burner control valves. 

Turn 

ON

 gas at LP cylinder.

Open lid during lighting.

To ignite, turn left knob to the 

HI

 position.

Push 

IGNITOR

  button rapidly.

6. 

If ignition does NOT occur in 5 seconds, turn the burner 

controls 

OFF

, wait 5 minutes and repeat the lighting 

procedure.

7.

 To ignite right burner, turn knob to the 

HI 

position.

If ignitor does not work, follow match lighting instructions. 

After Lighting: Turn knobs to 

HI

 position for warm-up. 

Turn controls and gas source or tank OFF when not 
in use.

WARNING

   rotate knobs from

 HI

 to 

LOW

. You should see 

Turning Grill Off

• Turn all knobs to  

OFF 

 position. Turn LP tank off by turning 

OPD hand wheel clockwise to a full stop.

Ignitor Check

• Turn gas off at LP tank.

 Press and hold ignitor button.  "Click" 

should be heard and spark seen each time between collector 
box or burner and electrodes. See 

"Troubleshooting"

 if no click 

or spark.

Valve Check

• Important: Make sure gas is off at LP tank before checking 

valves

.  Knobs lock in  

OFF 

 position. To check valves, first 

push in knobs and release, knobs should spring back. If knobs 
do not spring back, replace valve assembly before using grill. 
Turn knobs to

 LOW

 position then turn back to  

OFF 

 position. 

Valves should turn smoothly.  

• 

Plastic parts: 

Wash with warm soapy water and wipe dry.

 

Do not use citrisol, abrasive cleaners, degreasers or a 

concentrated grill cleaner on plastic parts. Damage to and 
failure of parts can result. 

• Porcelain surfaces: 

Because of glass-like composition, most 

residue can be wiped away with baking soda/water solution or 
specially formulated cleaner.

 

Use nonabrasive scouring powder 

for stubborn stains.

• Painted surfaces: 

Wash with mild detergent or nonabrasive 

cleaner and warm soapy water. Wipe dry with a soft 
nonabrasive cloth.

General Grill Cleaning 

• Do not mistake brown or black accumulation of grease and 

smoke for paint.  Interiors of gas grills are not painted at the 
factory 

(and should never be painted)

. Apply a strong solution 

of detergent and water or use a grill cleaner with scrub brush 
on insides of grill lid and bottom. Rinse and allow to completely 
air dry. 

Do not apply a caustic grill/oven cleaner to painted 

surfaces.

 

Sideburner Ignitor Lighting

1.

Turn 

OFF

 gas burner control valves.

2.

Turn 

ON

 gas at LP cylinder.

3.

To ignite SIDEBURNER, open sideburner cover.

4.

Turn sideburner knob to the 

HI

 position. Push IGNITOR 

button rapidly. 

5.

If sideburner does not light in 5 seconds, turn knob to 

OFF

wait 5 minutes, then repeat lighting procedure.

Strike the match.

 Be sure the burner lights and stays lit.

Be sure burner lights

and stays lit.

1.
2.

Turn 

OFF

 gas burner control valves. 

Turn 

ON

 gas at LP cylinder.

Push in and turn left knob to the 

HI

 position. 

Содержание 463721111

































Отзывы: