background image

12    

Burner Flame Check

Light burner, rotate knobs from HIGH to LOW. You should see 

a smaller flame in

 

LOW position than seen on HIGH. Always 

check flame prior to each use. If only low flame is seen refer to 

"Sudden drop or low flame" in the 

Troubleshooting Section

.

HI

LO

Match-Lighting

 Do not lean over grill while lighting.

1. Open lid during lighting.  
2.

Place match into match holder (hanging from side of cart).

3.

Push in and turn left knob to          PRE-HEAT position.  Be sure 
burner lights and stays lit.

4.

Hose Check

Before each use, check to see if hoses are cut, worn or kinked. 
Replace damaged hoses before using grill. Use only 
valve/hose/regulator specified in the Parts List.

Light right burner by pushing knob in and turning to 

PRE-HEAT 

position

Normal

Hose

Kinked
Hose

Turning Grill Off

Turn all knobs to  

OFF 

 position. Turn LP tank off by turning 

OPD hand wheel clockwise to a full stop.

Ignitor Check

Turn gas off at LP tank.

 Press and hold ignitor button.  "Click" 

should be heard and spark seen each time between collector 

box or burner and electrodes. See 

"Troubleshooting"

 if no click 

or spark.

Valve Check

Important: Make sure gas is off at LP tank before checking 

valves

.  Knobs lock in  

OFF 

 position. To check valves, first 

push in knobs and release, knobs should spring back. If knobs 

do not spring back, replace valve assembly before using grill. 

Turn knobs to

 LO

 position then turn back to  

OFF 

 position. 

Valves should turn smoothly.  

CAUTION

If ignition does NOT occur in 5 seconds, turn the 
burner controls OFF, wait 5 minutes and repeat the 
lighting procedure. If the burner does not ignite with 
the valve open, gas will continue to flow out of the 
burner and could accidently ignite with risk of injury.

Turn controls and gas source or tank OFF when not 
in use.

WARNING

Содержание 463631009

































Отзывы: