Chaparral VFS226 Скачать руководство пользователя

Страница: 94 / 108

VFS226 Rack/Desktop Model User’s Guide

D-6

Table D-2 describes the settings you can change here.

SNMP Configuration Screen

Option 3 from the Network Management System Console screen displays the SNMP
Configuration screen.

Table D-3 describes the settings you can change here.

Table D-2. System Configuration screen settings

Option

Setting

Description

IP Address

Internet Protocol address of the router. Default is 10.0.0.1.

IP Mask

Subnet mask. Default is 255.255.255.0.

Gateway

Default is 0.0.0.0. See your network administrator for more
information.

DHCP Enabled?

Yes or No toggle that enables or disables DHCP. Default is No
(disabled).

ESC

Exit

Saves all changes and returns to the Network Management
System Console screen

Содержание VFS226













































































































Результаты поиска

Содержание VFS226

Отзывы:

Похожие инструкции для VFS226

Бренды по названию

Популярные бренды

Chaparral VFS226, Руководство пользователя

Результаты поиска

Содержание VFS226

Отзывы:

Похожие инструкции для VFS226

Бренды по названию

Популярные бренды