manualshive.com logo in svg

Champion DH6000, Руководство по установке

Поделиться
Скачать
Champion DH6000 Скачать руководство пользователя страница 26

Installation

Converting 3 Phase to 1-Phase Operation 

1. 

Remove the paper insulator and jumper  

 

bars from the heater terminals.

2. 

Additional short jumper bars are  

 

stowed with the new data plate.

3. 

Reposition the jumper bars for 1PH as shown.

4. 

Reconnect the heater wires as shown.

5. 

Reinstall the paper insulator.

1. 

Remove the booster heater element cover.

2. 

Remove the paper insulator and  

 

jumper bars from the heater terminals.

3. 

Install the jumper bars for 1PH as shown.

4. 

Additional short jumper bars are stowed  

 

with the new data plate.

5. 

Connect the wires to the terminals as shown. 

6. 

Reinstall the paper insulator and the  

 

booster heater element cover.

Rewire Wash Tank Heater Element for 1PH

1 Phase 208-240/60/1

LINE IN

GRD

L1

L2

L1

L2

L3

JUMPER

Convert 

3 Phase to 1 Phase by installing of a  

jumper wire on the input power block and rewiring 
the wash tank and booster tank heaters. 
A jumper wire, jumper bars and a new data  
plate are stowed inside the control cabinet.

TO CONVERT: 

Install Main Terminal Block Jumper Wire

1. 

Disconnect all power to the machine.

2. 

Remove front panel to access the power terminal block. 

3. 

Connect jumper wire (shipped inside control cabinet)  

 

between L2 and L3 on output side of block.

4. 

Connect power on L1 and L2 of the terminal block.

1PH

L1

L2

L3

Rewire Booster Heater Element for 1PH

1PH

L3

L2

L1

Fig. 15

10

Содержание DH6000















































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды