Champion D-H1M5 Скачать руководство пользователя страница 11 | Manualshive

Страница: 11 / 77

Champion D-H1M5 Скачать руководство пользователя страница 11

1

Installation

!!ATTENTION!!
Use caution

when moving or lifting the dishwasher to prevent damaging the dishwasher

or the installation site.

Check doorway and passageway clearance before moving the dishwasher.

Remove dishwasher front panel and check under the machine base for obstructions before moving.

1.  Inspect the dishwasher for shipping damage
2.  Check the dishwasher interior for curtains, panels and other supplies.
3.  Lift the dishwasher off the shipping pallet and move the machine near its permanent location.

NOTE:

Refer to page 2 for instructions to remove the machine from the shipping pallet.

4. Leave a minimum of 6" between walls and the rear of the dishwasher.
5. Level the dishwasher side-to-side and front-to-back using a bubble level.

The dishwasher legs are adjusted by screwing them in or out.

6.  Do not remove tags attached to the utility connections.
7.  Remove the protective film from the dishwasher exterior.
8.  Remove any foreign material from the dishwasher interior.

Receiving

DHB, DH1, DLF

Corner Configuration

DHB, DH1, DLF

Straight-through Configuration

6" Min.

6" Min.

84"

DOOR

REMOVAL

75"

DOOR

UP

57-1/2"

MACH.

HEIGHT

34"

LOAD

HEIGHT

17"

CLEARANCE

«
...
9
10
11
12
13
...
»

Содержание D-H1M5














































































Отзывы:

Нет отзывов