Champion Power Equipment 92208 Скачать руководство пользователя страница 11

REV 92208-20120717  

8

92208

 

ENGLISH

ASSEMBLy

Your log splitter requires some assembly .
If you have any questions regarding the assembly of your 
log splitter, call our help line at 

1-877-338-0999 . Please 

have your serial number and model number available .

Open Shipping Crate

1 .  Set the shipping crate on a solid, flat surface .
2 .  Carefully cut the shipping bands and remove lid of 

shipping crate .

3 .  Locate all hardware before beginning assembly .

Assemble Tow Bar

1 .  Remove splitting beam lock pin that attaches beam to 

tow bar in horizontal position . (A)

2 .  Remove the 2 nuts and bolts that fasten the tow bar to 

the hydraulic oil tank . (B)

3 .  Slide the tow bar out to align the bolt holes (C) at the 

end of the tow bar with the mounting holes (D) on the 
the hydraulic tank .

4 .  With the tow bar in extended position, replace 2 nuts 

and bolts removed in step 2 and tighten to 47 .45 joules 
(35 ft-lb) . (E)

5 .  Remove 2 bolts and shipping bracket fastened to the 

bottom of the splitting beam near the pivot (F) . Discard 
shipping bracket and hardware .

6 .  Replace splitting beam lock pin removed in step 1 to 

secure beam in horizontal position . (G)

A

B

D

C

G

E

F

Log Splitter Location Cont’d.

Add Hydraulic Oil

1 .  Make sure the log splitter is on a flat, level surface .
2 .  Remove the oil plug from the oil tank . (A)
3 .  Add 18 .9 L (5 gal .) of hydraulic oil - 10W AW32, ASLE 

H-150, or ISO 32 are all acceptable types of fluid .

4 .  Check the hydraulic oil level using the oil sight glass .  

Oil level should visibly fill the glass sight . (B)

5 .  Replace and tighten the oil plug and orient the vent 

hole away from the operator zone . 

DO NOT remove the hydraulic oil fill cap when the engine 

is running or hot . Hot oil can escape causing severe 

burns . Always allow the log splitter to cool completely 

before removing the hydraulic oil cap . 

High fluid pressure and temperatures are created in the 

hydraulic log splitters . Hydraulic fluid will escape through 

a pin-size hole opening and can puncture skin and cause 

severe blood poisoning . 

Inspect hydraulic system regularly for possible leaks . 

Never check for leaks with your hand while the system 

is pressurized . Seek medical attention immediately if 

injured by escaping fluid .

WARNING

A

B

When temperature is below 0ºC (32ºF) use 
universal tractor/transmission fluid .

NOTE

Содержание 92208





























Отзывы: