manualshive.com logo in svg

Champion Power Equipment 100380, Руководство оператора, Страница: 26 / 54

Поделиться
Скачать
Champion Power Equipment 100380 Скачать руководство пользователя страница 26

100380 - REAR TiNE TiLLER

MAiNTENANCE

26

Tines

The tines will wear with use and should be inspected at the 
beginning of each tilling season and after every 30 operating 
hours. The tines can be replaced either individually or as a 
complete set. Refer to the parts list for tine identification and 
part numbers.

a. Tine Inspection:

With use, the tines will become shorter, narrower and pointed. 
Badly worn tines will result in a loss of tilling depth, and 
reduced effectiveness when chopping up and turning under 
organic matter.

B. Removing/Installing a Single Tine:

1.  With the engine shut off and the spark plug wire 

disconnected, remove the M10×25 bolt, lock washer, flat 
washer and M10 nut that attach a single tine to a tine 
holder. If needed, use penetrating oil on the nuts. 

2.  When installing a single tine, be sure to position it so that 

its cutting edge (sharp) will enter the soil first as the tiller 
moves forward.  Hand tighten completely.

C. Removing/Installing a Tine assembly:

1.  A tine assembly consists of eight tines mounted on a tine 

holder. 

2.  If removing both tine assemblies, mark them “left” and 

“right” before removal. Remove (2) pins and (2) cotter 
pins that secure the tine assembly to the tine shaft. If 
necessary, use a rubber mallet to tap the tine assembly 
outward off the shaft. 

3.  Before reinstalling the tine assembly, inspect the tine 

shaft for rust, rough spots or burrs. Lightly file or sand, as 
needed. Apply a thin coat of grease to the shaft. 

4.  Install each tine assembly so that the cutting (sharp) edge 

of the tines will enter the soil first when the tiller moves 
forward. 

5.  Bend cotter pins once inserted to prevent the pins from 

coming out.

Checking and Adjusting forward Drive belt 
Tension

It is important to maintain correct tension on the forward drive 
belt. A loose belt will cause the tines and wheels to slow down 
— or stop completely — even though the engine is running 
at full speed. A too-tight belt can result in unintentional tine 
movement when the lever is in the Neutral (released) position.

 

–

Check belt tension after the first two hours of break-in 
operation and after every 10 operating hours.

 

–

At the end of each tilling season, check the belt for cracks, 
cuts or frayed edges, and replace it as soon as possible.

To Check Belt Tension:

1.  Stop engine, wait for all parts to stop moving and 

disconnect spark plug wire. 

2.  With the forward and reverse lever in an open (released) 

position, measure and note the overall length of the 
cable spring by measuring from the outermost coil to the 
outermost coil. 

fORWARD LEVER

Содержание 100380























































Отзывы:

Нет отзывов