manualshive.com logo in svg

Champion Global Power Equipment 201047, Руководство оператора

Поделиться
Скачать
Champion Global Power Equipment 201047 Скачать руководство пользователя страница 15

201047 - 2400W DUAL FUEL INvERTER GENERATOR

ASSEMbLY

15

ASSEMbLY

Your generator requires some assembly. It must be properly 
serviced with fuel and oil before operation.

If you have any questions regarding the assembly of your 
generator, call our Technical Support Team at 1-877-338-0999. 
Please have your serial number and model number available.

Unpacking

1.  Set the shipping carton on a solid, flat surface.

2.  Remove everything from the carton except the generator.

3.  Using the carrying handles of the unit, carefully remove the 

generator from the box (two people lifting is recommended).

Add Engine Oil

 

WARNING

DO NOT attempt to crank or start the engine before it has been 
properly filled with the recommended type and amount of oil. 
Damage to the generator as a result of failing to follow these 
instructions will void your warranty.

 

NOTICE

The generator rotor has a sealed, pre-lubricated ball bearing 
that requires no additional lubrication for the life of the bearing.

 

NOTICE

The recommended oil type for typical use is 

10W-30 

automotive oil

. However, using the listed conventional oils 

shown in the “Recommended Engine Oil Type” chart may be 
used for typical use including the first 5 hours of the break-in 
run time period of the engine.

If running generator in extreme temperatures, refer to the 
“Recommended Engine Oil Type” chart.

-20

0

20

40

60

Ambient temperature

Recommended Engine Oil Type

80

100

120

-28.9

°F
°C

-17.8

-6.7

4.4

15.6

26.7

37.8

48.9

10W-30

5W-30 Full Synthetic

10W-40

5W-30

1.  Place the generator on a flat, level surface.

2.  Turn the oil access cover fastener to the unlocked position 

and remove the cover.

3.  Remove oil fill cap/dipstick to add oil.

4.  Using a funnel, add up to 13.5 fl. oz. (400 ml) of oil (included) 

and replace oil fill cap/dipstick and secure cover.  
DO NOT OVERFILL.

5.  Check engine oil level before each use and add as needed.

MAX

OIL DIP STICK

 

NOTICE

Once oil has been added, a visual check should show oil about 
1-2 threads from running out of the fill hole.

When using the dipstick to check oil level, DO NOT screw in 
the dipstick while checking.

Содержание 201047



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды