background image

32

Care of Your Opener

LIMIT AND FORCE ADJUSTMENTS

Weather conditions may cause 
some minor changes in door 
operation requiring some 
re-adjustments, particularly 
during the first year of operation.

Pages 27 and 28 refer to the 
limit and force adjustments. Only 
a screwdriver is required. Follow 
the instructions carefully.

Repeat the safety reverse test 
(Adjustment Step 3, page 29) 
after any adjustment of limits or force.

FORCE CONTROLS

1

3

9

7

5

1

3

9

7

5

LIMIT CONTROLS

KG

KG

THE REMOTE CONTROL BATTERY

The lithium battery should produce 
power for up to 5 years. 

To replace battery, use the visor 
clip or screwdriver blade to pry 
open the case as shown. Insert 
battery positive side up (+).

Dispose of old battery properly.

Replace the battery with ONLY 
3V2032 coin cell batteries.

NOTICE: To comply with FCC and or Industry Canada rules (IC), adjustment or modifications of this 
receiver and/or transmitter are prohibited, except for changing the code setting or replacing the 
battery. THERE ARE NO OTHER USER SERVICEABLE PARTS.
Tested to Comply with FCC Standards FOR HOME OR OFFICE USE. Operation is subject to the 
following two conditions: (1) this device may not cause harmful interference, and (2) this device 
must accept any interference received, including interference that may cause undesired operation.

To prevent possible SERIOUS INJURY or DEATH:
•  NEVER allow small children near batteries.
•  If battery is swallowed, immediately notify doctor.
To reduce risk of fire, explosion or chemical burn:
• Replace ONLY with 3V2032 coin batteries.
• Do NOT recharge, disassemble, heat above 100°C (212°F) 
 or incinerate.

MAINTENANCE SCHEDULE

Once a Month

•  

Manually operate door. If it is unbalanced or binding, 
call a trained door systems technician.

•  

Check to be sure door opens and closes fully. Adjust 
limits and/or force if necessary. (See pages 27 and 28)

•  

Repeat the safety reverse test. Make any necessary 
adjustments. (See Adjustment Step 3)

Once a Year

•  

Oil door rollers, bearings and hinges. The opener does 
not require additional lubrication. Do not grease the door 
tracks.

Battery 
positive 
side up (+)

Содержание Whisper Drive Security+ HD700DS









































Отзывы: