background image

26

ALL ONE-PIECE DOORS

1. Assemble the door arm, Figure 4:

• Fasten the straight and curved door arm sections

together to the longest possible length (with a 2 or 3
hole overlap).

• With the door closed, connect the straight door arm

section to the door bracket with the 5/16"x1-1/4" 
clevis pin.

• Secure with a ring fastener.

2. Adjustment procedures, Figure 5:

• On one-piece doors, before connecting the door arm

to the trolley, the travel limits must be adjusted. Limit
adjustment screws are located on the left side panel
as shown on page 27. Follow adjustment procedures
below.

• Open door adjustment: decrease UP travel limit

- Turn the UP limit adjustment screw counter-clockwise

4 turns.

- Press the Door Control push button. The trolley will

travel to the fully open position.

- Manually raise the door to the open position (parallel

to the floor), and lift the door arm to the trolley. The
arm should touch the trolley just in back of the door
arm connector hole. Refer to the fully open
trolley/door arm positions in the illustration. If the arm
does not extend far enough, adjust the limit further.
One full turn equals 2" (5 cm) of trolley travel.

• Closed door adjustment: decrease DOWN travel

limit

- Turn the DOWN limit adjustment screw clockwise

4 complete turns.

Nuts
5/16"-18

Lock
Washers
5/16"

Ring
Fastener

Straight
Arm

Bolts
5/16"-18x7/8"

Door
Bracket

Clevis Pin
5/16"x1-1/4"

Curved
Door Arm

- Press the Door Control push button. The trolley will

travel to the fully closed position.

- Manually close the door and lift the door arm to the

trolley. The arm should touch the trolley just ahead of
the door arm connector hole. Refer to the fully closed
trolley/door arm positions in the illustration. If the arm
is behind the connector hole, adjust the limit further.
One full turn equals 2" (5 cm) of trolley travel.

3. Connect the door arm to the trolley:

• Close the door and join the curved arm to the

connector hole in the trolley with the remaining clevis
pin. It may be necessary to lift the door slightly to make
the connection.

• Secure with a ring fastener.

• Run the opener through a complete travel cycle. If the

door has a slight “backward” slant in full open position
as shown in the illustration, decrease the UP limit until
the door is parallel to the floor.

NOTE:

When setting the up limit on the following page, the

door should not have a “backward” slant when fully open
as illustrated below. A slight backward slant will cause
unnecessary bucking and/or jerking operation as the door
is being opened or closed from the fully open position.

Figure 4

Door Arm

Closed
Door

Outer Trolley

Emergency Release Handle

Open Door

Door with
Backward Slant
(Incorrect)

Correct Angle

Inner Trolley

Inner Trolley

Outer Trolley

Figure 5

Содержание Security+ HD200D









































Отзывы: