Chamberlain Security+ 2580 Скачать руководство пользователя | Manualshive

Страница: 10 / 36

background image

10

INSTALLATION STEP 2

Install the Header Bracket

You can attach the header bracket either to the wall
above the garage door, or to the ceiling. Follow the
instructions which will work best for your particular
requirements. Do not install the header bracket
over drywall. If installing into masonry, use
concrete anchors (not provided).

WALL HEADER BRACKET INSTALLATION

• Center the bracket on the vertical centerline with

the bottom edge of the bracket on the horizontal
line as shown (with the arrow pointing toward the
ceiling).

• Mark the vertical set of bracket holes (do not use

the holes designated for ceiling mount). Drill 3/16"
pilot holes and fasten the bracket securely to a
structural support with the hardware provided.

Lag Screw
5/16"-9 x 1-5/8"

HARDWARE SHOWN ACTUAL SIZE

Lag Screws
5/16"-9x1-5/8"

Highest Point of
Garage Door Travel

Vertical
Centerline

Header
Wall

Garage
Door

UP

CEILING MOUNT ONLY

Wall Mounting Holes

Optional
Wall Mounting Holes

The nail hole is for
positioning only.
You must use lag screws
to mount the header bracket.

UP

CE

ILIN

G M

OU

NT

O

NL

Y

Door Spring

Header

Bracket

2x4
Structural
Support

Vertical
Centerline

UP

CEILING MOUNT ONLY

Ceiling Mounting Holes

The nail hole is for
positioning only.
You must use lag screws
to mount the header bracket.

UP

Lag Screws
5/16"-9x1-5/8"

Garage Door

Vertical Centerline

Header Wall

– Finished Ceiling –

Header

Bracket

6" Maximum

Vertical
Centerline

Door
Spring

CEILING HEADER BRACKET INSTALLATION

• Extend the vertical centerline onto the ceiling as

shown.

• Center the bracket on the vertical mark, no more

than 6" from the wall. Make sure the arrow is
pointing toward the wall. The bracket can be
mounted flush against the ceiling when clearance
is minimal.

• Mark the side holes. Drill 3/16" pilot holes and

fasten bracket securely to a structural support with
the hardware provided.

«
...
8
9
10
11
12
...
»

Содержание Security+ 2580





































Отзывы:

Нет отзывов

Похожие инструкции для Security+ 2580

2-IN-1 SAFETY CAN OPENER

Бренд: Lantana Страницы: 2

Rinku-GLink RH-GGO-KIT

Бренд: G-Light Страницы: 2

Бренд: CAME Страницы: 30

SURF 350 Reversible

Бренд: SEA Страницы: 20

Whisper Drive Security+ 257858

Бренд: Chamberlain Страницы: 80

SPACELITE HT150

Бренд: BUTZBACH Страницы: 45

Бренд: Chamberlain Страницы: 286

Бренд: ARC Страницы: 8

Бренд: Seaside Страницы: 33

LiftMaster 84501

Бренд: MyQ Страницы: 40

Бренд: DTS Страницы: 12

Бренд: DCS Страницы: 17

GDO-6v3 EasyRoller

Бренд: Automatic Technology Страницы: 36

Бренд: Chamberlain Страницы: 3

Бренд: Chamberlain Страницы: 12

Бренд: CAME Страницы: 64

Бренд: Beninca Страницы: 20

Бренд: CAME Страницы: 24

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды