To Open the Door Manually
The door should be fully
closed if possible. Pull down
on the emergency release
handle and lift the door
manually. To reconnect the
door to the opener, press the
door control push bar.
The
lockout feature
prevents
the trolley from reconnecting
automatically. Pull the
emergency release handle
down and back (toward the
opener). The door can then
be raised and lowered
manually as often as
necessary. To disengage the
lockout feature, pull the
handle straight down. The
trolley will reconnect on the
next UP or DOWN operation,
either manually or by using
the door control or remote.
To prevent possible SERIOUS INJURY or DEATH from a
falling garage door:
• If possible, use emergency release handle to
disengage trolley ONLY when garage door is CLOSED.
Weak or broken springs or unbalanced door could
result in an open door falling rapidly and/or
unexpectedly.
• NEVER use emergency release handle unless garage
doorway is clear of persons and obstructions.
• NEVER use handle to pull door open or closed. If
rope knot becomes untied, you could fall.
27
Trolley
Release
Arm
NOTIC
E
Emergency
Release
Handle
(Pull Down)
Trolley
Release
Arm
NOTICE
Emergency
Release Handle
(Down and Back)
WARNING
CAUTION
WARNING
WARNING
LOCKOUT POSITION
MANUAL DISCONNECT
POSITION
Using the Wall-Mounted
Door Control
THE MULTI-FUNCTION DOOR CONTROL
Press the push button to open or
close the door. Press again to
reverse the door during the closing
cycle or to stop the door while it's
opening.
Light feature
Press the Light button to turn the opener light on or
off. It will not control the opener lights when the door
is in motion. If you turn it on and then activate the
opener, the light will remain on for 4-1/2 minutes.
Press again to turn it off sooner. The 4-1/2 minute
interval can be changed to 1-1/2, 2-1/2, or 3-1/2
minutes as follows: Press and hold the Lock button
until the light blinks (about 10 seconds). A single blink
indicates that the timer is reset to 1-1/2 minutes.
Repeat the procedure and the light will blink twice,
resetting the timer to 2-1/2 minutes. Repeat again for
a 3-1/2 minute interval, etc., up to a maximum of four
blinks and 4-1/2 minutes.
Lock feature
Designed to prevent operation of the door from
hand-held remote controls. However, the door will
open and close from the Door Control, the Outside
Keylock and the Keyless Entry Accessories.
To activate, press and hold the Lock button for 2
seconds. The push bar light will flash as long as the
Lock feature is on.
To turn off, press and hold the Lock button again for
2 seconds.The push bar light will stop flashing. The
Lock feature will also turn off whenever the “learn”
button on the motor unit panel is activated.
Additional features when used with the
3-Button hand-held remote
A) To control the opener lights:
In addition to operating the door, you
may program the remote to operate the lights.
1. With the door closed, press and hold a small
remote button that you want to control the light.
2. Press and hold the Light button on the
Multi-Function door control.
3. While holding the Light button, press and hold the
Lock button on the door control.
4. After the opener lights flash, release all buttons.
LOCK
LIGHT
P
u
sh
B
u
tton
Lock
B
u
tton
Light
B
u
tton
B) To operate one door using all three buttons on the
hand-held remote:
You may program the remote to open
the door with the large button, close
it with the middle button, and stop the
door’s movement with the third
button.
NOTE:
If remote is already programmed,
you must first erase all codes. See Programming.
1. With the door closed, press and hold the large
remote push button.
2. Press and hold the Lock button on the door
control.
3. Press and hold the door control push bar.
4. After the opener lights flash, release all buttons.
Open
Close
Stop
